Hoover C1633 - Manual (Page 6)

6
2.4 2.5
La courroie
Tou rne r l’a spi rat eur à l ’en ver s.
Ret ire r la pl aqu e in fér ieu re par de s v err ous de
lib érat ion .
Pla cer l a cou rro ie s ur l a pou lie .
Le cфt й d e la co urro ie l e p lus pr ès d e l’a ppa rei l d evr ait être
alig né a vec les bo uto ns s ailla nts au bas de l’a spi rat eur .
Rep lac er l a pla que i nfé rie ure e n met tan t les
bou ton s s aill ant s à l’av ant de la pl aqu e d ans le
por te- con duc teu r de l ’ap par eil.
Vér ifier si les la ngu ett es son t re pou ssée s e t n e s ont
pas c ouv ert es p ar l a pla que .
Bie n pla cer l a pla que i nfé rie ure p ar- des sus l ’ag ita teu r
et l a lan gue tte .
Pou r vér ifi er l a cou rro ie, r eti rer l a pla que i nfé rie ure ( voi r la s ect ion s uiv ant e).
Si l a c our roi e e st éti rée , c oup ée ou sec tio nné e, o u s i le ro ule au- bro sse ag ita teu r e st rem pla cé, re mpl ace r
aus si l a cou rro ie.
Lib ére z la c ein tur e usé e de l a pou lie .
Sou lev er l ’ag ita teu r, r eti rer l’a nci enn e c our roi e e t p lac er la nou vel le cou rro ie dan s la ra inur e de l’a git ate ur.
Rep lac er l’a git ate ur en alig nan t le bo uto n s aill ant, si tu й а un e e xtr ém ité de l’a git ate ur, ave c la fe nte
dan s la p aro i de l a bas e de l ’as pir ate ur.
Pu is p ous ser l ’ag ita teu r ver s le b as.
Quand remplacer
Remplacement
Déb ran che r l’a ppa rei l ava nt d e vér ifi er o u de r em pla cer l a cou rro ie.
La courroie : Quoi acheter
N’u tili ser po ur vot re asp ira teu r q ue des cou rro ies de m arq ue HO OV ER.
Pou r l’ ach at d ’un e n ouv elle cour roi e, d em and er la piè ce H oov er n o 4 478 3.
Rep lac er l e v ide -po uss ièr e d ans le su ppo rt a u b as d u sa c e t
ver rou ille r les l ang uet tes e n pos itio n.
Pou r e mpê che r le s fu ite s, s ’as sur er q ue le vid e-p ous siè re est
pla cé com plè tem ent da ns l e jo int d’ éta nch éité et qu ’il rep ose
à pla t con tre c ond uit à p ous siè re c om me i l est i llu str é.
2.6
2.3
CORRECT INCORRECT
Vidage (continu)
6
2.4
2.6
2.5
The Belt
Turn cleaner over.
Remove bottom plate by releasing latches.
Place belt on pulley.
Side of belt nearer cleaner should be in line with
projections on bottom of cleaner.
Replace bottom plate, by putting knobs on front
of plate into wire holders on cleaner.
Check to see that latches are pushed back and will not
be covered by plate.
Position bottom plate over agitator and latch securely.
To check belt, remove the bottom plate (see following section).
If the belt is stretched, cut, broken, or if the agitator brushes are being replaced, replace the belt.
Release worn belt from pulley.
Lift out agitator, remove old belt and place new belt in groove of agitator.
Replace agitator by aligning the projection, located on one end of the agitator, with the slot in the wall
of the cleaner base.
Then push the agitator down into position.
When to Replace
How to Replace
Disconnect cleaner form electrical outlet before checking or replacing belt.
Belt: What to Buy
Use only genuine HOOVER belts with your cleaner.
When purchasing a new belt, ask for HOOVER part No. 44783.
2.3
CORRECT INCORRECT
Reposition cup up into support at bottom of bag and snap
latches into position.
To prevent leaking, make sure dirt cup is positioned fully into
seal at top of cup and is flat against the dirt tube as shown.
How to Empty (cont.)