beautypg.com

Maytag 27 Inch Gas Smart Dryer Quick Reference Sheet User Manual

Warning, Dryer quick start guide, Operating instructions

background image

W11356335A

W11356663A-SP

Dryer Quick Start Guide

OPERATING INSTRUCTIONS

WARNING

Fire Hazard

No washer can completely remove oil.
Do not dry anything that has ever had any type of oil

on it (including cooking oils).
Items containing foam, rubber, or plastic must be

dried on a clothesline or by using an Air Cycle.
Failure to follow these instructions can result in

death or fire.

WARNING

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from dryer.
Do not dry anything that has ever had anything

flammable on it (even after washing).
Failure to follow these instructions can result in

death, explosion, or fire.

WARNING:

To reduce the risk of fire, electric shock, or injury to persons,

read the IMPORTANT SAFETY INSTRUCTIONS, located in your

appliance's Owner's Manual, before operating this appliance.

Step 1. Clean Lint Screen

Step 2. Load Clothes; then Close

Door

Step 3. Power On/Cancel

Step 4. Select Cycle and Settings

Step 5. Press Start/Pause

Cycle Guide – Normal Cycle

If settings are changed, the new settings will be remembered. If there is a power failure, settings will return to the

default. Not all features and cycles are available on all models. Not all settings and options are available on each

cycle.

Use Sensor Cycle for better fabric care and energy savings.

The dryer senses moisture in the load or air temperature and shuts off when the load reaches the selected dryness

level. Temperatures shown in

bold

are the default settings for that cycle.

Items to Dry:

Cycle:

Temperature:

Description:

Work clothes,

casual wear, mixed

cottons, sheets,

corduroys

Normal

Medium High

Uses Medium High heat to dry large loads of mixed

fabrics and items. Use Normal cycle to increase

energy saving versus Regular cycle by using a slightly

lower heat level.

On steam models, you may select the “+ Steam” setting to add a short steam cycle after 60 minutes. This is

available only with High and Medium drying temperature settings.

NOTE:

Government energy certifications for this model were based on the Normal cycle, Highest temperature

setting, Normal dryness level. The as-shipped defaults were the same as the government energy certification

settings except the default temperature setting of Medium High was adjusted to the Highest temperature setting.

Online Ordering Information

For detailed installation instruction and maintenance information, winter storage, and transportation tips, please

see the Owner’s Manual included with your machine.
For information on any of the following items, the full cycle guide, detailed product dimensions, or for complete

instructions for use and installation, please visit https://www.maytag.com/owners, or in Canada

https://www.maytag.ca/owners. This may save you the cost of a service call.

However, if you need to contact us, use the information listed below for the appropriate region.
United States:

1–800–344–1274
Maytag Brand Appliances

Customer eXperience Center

553 Benson Road

Benton Harbor, MI 49022–2692

Canada:

1–800–688–2002
Maytag Brand Appliances

Customer eXperience Centre

200–6750 Century Ave.

Mississauga, Ontario L5N 0B7

Button Descriptions

1. POWER/CANCEL

Touch to turn the dryer on and off. Touch to stop/cancel a cycle at any time.

2. CYCLE CONTROL KNOB

Use the Cycle Control knob to select available cycles on your dryer. Turn the knob

to select a cycle for your laundry load. See the online “Cycle Guide” for details.
The Cycle Control Knob can also be pressed to activate the Extra Power option for

harder-to-dry loads. See the “Options” section for more information.

3. START/PAUSE

Touch and hold until the LED comes on to start a cycle. Touch Start during a cycle

to pause it.

4. LED DISPLAY AND SETTINGS

When you select a cycle, its default settings will light up and the estimated time

remaining (for Sensor cycles) or actual time remaining (for Timed cycles) will be

displayed. Touch the setting names next to the display to adjust settings. See

online “Cycle Guide” for details. Not all settings are available with all cycles.

More Time/Less Time

Touch More Time or Less Time with Timed Cycles to increase or decrease the

length of a Timed Dry or Quick Dry cycle.

Not all features, cycles, and options are available on all models. Appearance may vary.

NOTE:

The control panel features a sensitive surface that responds to a light touch of your finger. To ensure your selections are registered, touch the control

panel with your finger tip, not your fingernail. When selecting a setting or option, simply touch its name.

Temp

When using any cycle except Sanitize, you may select a dry temperature based on

the type of load you are drying. Use the warmest setting safe for the garments in the

load. Follow garment label instructions.

Dryness

When using Sensor Cycles (except for the Sanitize cycle), you may select a Dryness

Level based on the type of load you are drying.

NOTE:

Dryness Level is for use with Sensor Cycles only.

5. OPTIONS

Use to select available options for your dryer. Not all cycles and options are

available on all models.

Wrinkle Prevent

If you will be unable to remove a load immediately, touch Wrinkle Prevent to add up

to 150 minutes of periodic tumbling to help reduce wrinkling. On steam models, on

some cycles, you may select the “+Steam” setting to add a short steam cycle after

60 minutes to help smooth out wrinkles.

Steam

Steam adds steam to the end of certain Sensor Cycles to help smooth wrinkles. It is

not available on Sanitize, Delicates, Steam Refresh, or Timed Cycles (Timed Dry,

Quick Dry). Steam can be used with High, Medium High, or Medium heat settings.

This option adds approximately 15 minutes to the total cycle time.

Cycle Signal

Use this to turn the signal indicating the end of a drying cycle on or off. Touch and

hold Reduce Static for 3 seconds to turn sounds on or off.

Control Lock

Use to lock the controls of the dryer and avoid an accidental change in cycle options

or preferences during a drying cycle. Touch and hold Steam for 3 seconds to lock or

unlock the controls of the dryer. During this time, the LED display will count down “3-

2-1.” Once the controls are locked, the Control Lock icon will illuminate.

NOTE:

The Control Lock function may be enabled when recovering from a power

failure. To unlock the control, touch and hold Steam for at least 3 seconds.

Reduce Static

Touch to add this option to selected Automatic/Sensor Cycles. The dryer will

automatically tumble, pause, and introduce a small amount of moisture into

the load to help reduce static. This option adds approximately 3 minutes to the

total cycle time.

Extra Power

The Extra Power option can be used with both Sensor and Timed Dry Cycles.

Press the Cycle Control knob to activate the Extra Power option, which

provides an additional 10 minutes of cycle time (including additional heat and

tumbling, where applicable). When Extra Power is activated, the Cycle Control

knob will illuminate and the estimated time remaining on the display will show

an additional 10 minutes.

6. CONNECTIVITY

Use to select available connectivity options for your dryer. Not all cycles and

options are available on all models. Download the Maytag

app and follow

the instructions to connect your dryer to your home Wi-Fi network. You may

also visit

www.maytag.com/connect

.

7. CYCLE STATUS AND CONNECTED STATUS

The Cycle Status indicators show the progress of a cycle. The Connected

Status indicators show the connected status. Not all indicators are available

on all models.

Sensing

The Sensing indicator will light during Sensor Cycles to indicate that the

moisture sensor on the dryer is operating. This indicator will not light during

Timed Cycles or options such as Wrinkle Prevent.

Wet

The load is still wet and/or the cycle just started.

Damp

The load still has moisture remaining, a good point in the cycle to remove a

garment or air dry or iron.

Cool Down

The dryer has finished drying with heat and is now tumbling the load without

heat to cool it down and reduce wrinkling.

Check Vent

This indicator will show the status of airflow through the dryer and the dryer

vent system for the dryer’s life. This feature is available during Sensor and

Steam Cycles only. During the sensing phase at the beginning of the cycle,

the Check Vent light will come on if a blocked vent or low airflow issue is

detected. This light will stay on for the entire cycle.
The light will be cleared upon completion of the cycle, touching Power, or

opening the door. It will continue to illuminate during the cycle unless the root

cause is resolved.

NOTE:

The dryer will continue to operate even while the indicator is lit, but

poor airflow can impact dry times and overall performance. If there are other

error issues during a cycle, the Check Vent indicator will not light up. Refer to

the online “Troubleshooting” section.

End

This will indicate that the selected cycle has ended and the load may be

removed from the dryer. If Wrinkle Prevent has been selected, the dryer may

continue to tumble the load, even if “End” is displayed.

Control Lock

This will illuminate once the controls are locked.

NOTE:

The Control Lock function may be enabled when recovering from a

power failure. To unlock the control, touch and hold Steam for at least 3

seconds.

Connected

This will illuminate when the dryer is connected to the internet.

Smart Delay

This will illuminate when a Smart Delay is in effect: the operation of the

dryer has been delayed to a time when lower utility rates are in effect.