Amana 27 Inch Front Load Electric Dryer Owner Manual - Manual (Page 6)

6
CONTROL PANEL AND FEATURES
POWER
Touch to turn the dryer on and off. Touch to stop/cancel
a cycle at any time.
CYCLES
Touch a button for the desired drying cycle. See “Cycle
Guide” for cycle details.
START/PAUSE
Touch and hold until LED counts down “3-2-1” and the
dryer starts; then let go to start a cycle, or touch once
while a cycle is in process to pause it.
MODIFIERS
Use to select available modifiers for your dryer. Not all
cycles and options are available on all models.
Temp
When using Timed Dry/Quick Cycle, you may select
a dry temperature based on the type of load you are
drying. Use the warmest setting that is safe for the
garments in the load. Follow garment label instructions.
Dryness
You may adjust the Dryness on Sensor cycles (except
for the Sanitize cycle), if desired.
NOTE: Dryness is for use with Sensor cycles only.
More Time/Less Time Timed Dry Adjust
Touch MORE TIME or LESS TIME with the Timed Dry/
Quick cycle to increase or decrease the length of the
cycle.
OPTIONS
Use to select available options for your dryer. Not all cycles
and options are available on all models.
Wrinkle Prevent Option
If you will be unable to remove a load immediately,
touch WRINKLE PREVENT to add up to 150 minutes
of periodic tumbling to help reduce wrinkling.
NOTE: If you open the dryer door prior to the end
of the Wrinkle Prevent option, the dryer will go into
standby.
Cycle Signal
Use this option to turn the signal indicating the end
of a drying cycle to low, medium, high, or off. The
volume you select here will also be applied to the
Damp Dry Signal.
1
2
3
4
5
Not all features and cycles are available on all models.
NOTE: You may also turn off the tones that sound
when a feature, setting, or option is touched. Touch
and hold CYCLE SIGNAL for about 3 seconds to turn
sounds to low, medium, high, or off.
Damp Dry Signal
Touch to turn the Damp Dry Signal on or off. When
selected, a series of beeps will sound when the load
is damp, but not completely dry. This will allow you to
take clothes out of the load that do not need to dry
completely. This option is available on some cycles.
The Damp Dry signal is selected as a default for the
Bulky Items/Normal, Bulky Items/Wrinkle Control,
and Bulky Items/Heavy Duty cycles, as a reminder
to manually reposition bulky loads midway through
the cycle.
Control Lock
Use this option to lock the controls of the dryer
and avoid an accidental change in cycle options
or preferences during a drying cycle.
Touch and hold CONTROL LOCK for 3 seconds to
lock or unlock the controls of the dryer. During this
time, the LED Display will count down “3-2-1.”
Once the controls are locked, the LED Display
will display “Loc.”
NOTE: The Control Lock function may be enabled
when recovering from a power failure. To unlock the
control, touch and hold CONTROL LOCK for at least
3 seconds.
Eco Dry Option
The Eco Dry option will default on only for the Normal
cycle and is only available on that cycle. This option
allows you to increase your energy savings by using
a slightly lower heat level. The Eco Dry option will
increase drying times by approximately 40 minutes,
which will be reflected on the LED Display. If optimal
time is desired, touch ECO DRY to turn off this option.
LED DISPLAY
When you select a cycle, its default settings will light up
and the Estimated Time Remaining (for Automatic Cycles)
will vary depending on the cycle selection, or actual time
remaining for Timed Dry cycles (for Manual Cycles) will be
displayed.
6
NOTE: The control panel features a sensitive surface that responds to a light touch of your finger. To ensure your selections are
registered, touch the control panel with your fingertip, not your fingernail. When selecting a setting or option, simply touch the
appropriate button.
1 2 3 6
4
4 5
5