Electrolux EI27EW35J S - Manual (Page 3)

27" Combination Installation Specifications
• Always consult local and national electric codes.
(Refer to product-specific electrical specifications on this page.)
• Minimum 23-1/2" deep cutout dimension is critical for proper
combination installation, to ensure that each built-in product’s faceplate
will fit flush against cabinet front.
• Bases must be level and cabinet front must be square.
• Minimum 4-1/2" required distance from bottom of Wall Oven cutout
to floor, 31" suggested.
• Respect critical dimensions as noted for proper installation of built-In
products.
• Minimum 21" clearance needed for Wall Oven door depth when open.
27" Built-In Microwave Specifications
• Product Weight – 79 Lbs.
• Voltage Rating – 120V / 60 Hz / 15 Amps
• Connected Load (kW Rating) @ 120 Volts = 1.6 kW
(For use on adequately wired 120V, dedicated circuit having 2-wire
service with a separate ground wire. Appliance must be grounded
for safe operation.)
• Amps @ 120 Volts = 13.7 Amps
• Full oven base of solid plywood or similar material required, capable of
supporting 150 Lbs.
• Minimum 2-1/8" clearance required from bottom of Built-In Microwave
cutout to top edge of Wall Oven’s faceplate, leaving a 2" visible gap
between both product faceplates.
27" Electric Single Wall Oven Specifications
• Product Weight – 150 Lbs.
• Single phase 3- or 4-wire cable, 120 / 240 or 120 / 208 Volt, 60 Hertz
AC only electrical supply with ground required on separate circuit fused
on both sides of line.
• Connected Load (kW Rating) @ 240 / 208 Volts = 3.4 / 2.6 kW
• Amps @ 240 / 208 Volts = 14.2 / 12.6 Amps
• Full oven base of solid plywood or similar material required, capable of
supporting 150 Lbs.
• To adapt oven to fit cutout height between 27-5/8" and 28-1/4", add
one 2"-wide wood shim of appropriate height to each side of opening
under oven side rails. Lifting oven will hide larger cutout opening at
top and oven’s 1"-high bottom trim will hide shims at bottom.
(Standard 1"- High Bottom Trim included.)
• To adapt oven to fit cutout height between 28-1/4" and 30", optional
3"- High Bottom Trim available.
Note: For planning purposes only. Refer to Product Installation Guide
on the web at electroluxappliances.com for detailed instructions.
27" Combination Installation –
Built-In Microwave/Single Wall Oven
High standards of quality at Electrolux Home Products, Inc. mean
we are constantly working to improve our products. We reserve the right
to change specifications or discontinue models without notice.
Electrolux Major Appliances, N.A.
USA • 250 Bobby Jones Expressway • Augusta, GA 30907 • 1-877-4electrolux (1-877-435-3287) • electroluxappliances.com
CANADA • 5855 Terry Fox Way • Mississauga, ON L5V 3E4 • 1-800-265-8352 • electroluxappliances.ca
MODD_EW 27INST EL 01/10 © 2010 Electrolux Major Appliances, NA Printed in the U.S.A.
* Minimum 2 1 /
8
" clearance required from bottom
of Built-In Microwave cutout to top edge of
Wall Oven’s faceplate, leaving a 2" visible gap
between both product faceplates.
** Critical dimension – MUST be applied
† For cutout height between 27 5 / 8 " and 28 1 / 4 "
add one 2"-wide wood shim of appropriate
height to each side of opening under oven
side rails. Lifting oven will hide larger cutout
opening at top and oven’s 1"-high bottom trim
will hide shims at bottom.
(Optional 3"-high
bottom trim available for cutout height
between 28
1 / 4 " and 30".)
For detailed product dimensions
and installation specifications, refer
to model-specific product page and
installation guide on web
27" Electric Single
Wall Oven Cutout
For models:
EW27EW55G
EI27EW35J
27" Built-In
Microwave Cutout
For model:
EW27MO55H
Full plywood base
required to support
150 lbs.
120V/60 Hz
grounded electrical
MUST be located
within shaded area
21" min.
21 1 /
2
" max. 25 1 / 8 " min.
25 5 /
8
" max.
24" min.
3"
27 1 /
4
" min.
27 5 / 8 " max.
4"x 4" opening
to route armored
cable
23 1 / 2 " min.**
(critical
dimension)
2" min.
31"
suggested
distance
4 1 /
2
"
min.
required
Full base required
to support 150 lbs.
Electrical junction
box location
2"
(visible
gap)*
27 1 /
8
" min.
24 7 / 8 " min.
25 1 /
4
" max.
2"-wide
wood spacers
(if needed) †