Electrolux TM-75 - Manual (Page 17)

17
DIAGRAM 1 --- TM-75 PARTS LIST
Loc P/N Description Qty Loc P/N Description Qty
1 185108 Frame Assy (incl. 2-8) 1 53 185243 Assy, Blade Guard (incl. 54-61) 1
2 185106 Frame 1 54 185241 Guard, Blade 8in - Machined 1
3 185107 Bar, Roller Guide 1 55 185150 Adaptor - Y Water Tube 1
4 185159 Clamp, Roller Bar Adj. 1 56 185257 Tube, Water 6 x 4 x 280mm 2
5 173019 Lockwasher, External Tooth, M8 2 57 185140 Knob, M8 x 45 1
6 167478 Capscrew, Hex Hd M8 x 1.25 x 25mm 2 58 185141 Screw, M4 x 20mm 1
7 139746 Washer, Flat M6 1 59 185244 Flap, Splash 1
8 185255 Screw, Mach Pan Hd M6 x 1.0 x 10mm 1 60 020762 Washer, Flat .250 SAE 1
9 185111 Water Tray 1 61 185251 Capscrew, Soc Bt Hd M6 x 1.0 x 10mm SS 1
10 185130 Assy, Cutting Table (incl. 11-24) 1 62 185237 Blade, 8in (200mm) Cont Rim 1
11 185136 Cutting Table 1 63 185160 Bracket, Pump Mounting 1
12 185125 Bracket, U Roller 1 64 185132 Assy, Water Pump (incl. 65-66) 1
13 185126 Stud, Upper U Roller 2 65 185146 Water Pump 115V/60Hz 1
14 185127 Stud, Lower U Roller 2 66 185158 Adaptor, 90° Tube - Water Pump 1
15 185137 Roller, U Shaped Nylon 4 67 185201 Tube, Water 8 x 6 x 600mm 1
16 139745 Locknut, Fiber M6 x 1.0 4 68 169887 Guide, Rip - Plain 1
17 139737 Capscrew, Hex Hd M8 x 1.25 x 20mm 4
18 185129 Bracket, Single Roller 1
19 172027 Nut, Hex Hd M8 x 1.25 5 ---- Items Not Shown ----
20 185138 Roller, Right Side Nylon 1 P/N Description Qty
21 185131 Stud, Single Roller 1 169866 Decal, Felker Rip Guide 1
22 173019 Lockwasher, External Tooth, M8 4 185262 Decal, TM-75 Pan 1
23 173059 Washer, Flat M8 4 185263 Decal, TM-75 Motor Cover 1
24 139738 Locknut, Fiber M8 x 1.25 4 185264 Decal, Felker 8" [200mm] Guard 1
25 185245 Assy, Power Head w/ Guard (incl. 26-53) 1 187043 Decal, Warning 1
26 185235 Bracket, Motor Base Wldmnt 1 189247 Decal, Water Pump Outlet 1
27 185260 Plate, Spacer 1
28 185221 Motor Assy, 3/4HP 4.2A 115V (incl. 29-35) 1 192001 Wrench, Allen 4mm 1
29 185216 Spacer Sleeve (Before S/N 417841) 1 185233 Wrench, Allen 5mm 1
(See Note 1) 185145 Wrench, Open [17 x 13] 1
30 185215 Seal, Shaft (Before S/N 417841) 1 185272 Wrench, Box/Open [18 x 10] 1
(See Note 1)
31 185218 Flange, Inner (Before S/N 417841) 1 187076 90° Adjustable Protractor 1
(See Note 1) 187077 Dual 45° Angle Guide 1
-- 542190504 Flange, Inner (S/N 417841 & Later) 1 187078 Bull Nose Miter Guide 1
(See Note 1)
32 185219 Outer Flange 1
33 185220 Nut, Arbor M12 1
34 185248 Cover, Fan 1
35 185274 Slinger, Shaft 1
36 185239 Cover, Motor - Machined 1
37 185238 Bushing, Strain Relief 2
38 185214 Capacitor 1
39 185246 Cord, 16/3 SJTW w/ Male Plug 1
40 185247 Cord, 16/3 SJTW w/ Female Plug 1
41 020762 Washer, Flat .250 SAE 4
42 163689 Lockwasher, Split M6 5
43 185252 Capscrew, Soc Bt Hd M6 x 1.0 x 16mm SS 4
44 185253 Switch, Toggle 3/4hp 1
45 090552 Plate, Switch 1
46 032503 Shim, Brass .020 5
47 173059 Washer, Flat M8 1
48 185258 Capscrew, Soc Bt Hd M6 x 1.0 x 40mm SS 1
49 020782 Lockwasher, Split #10 7
50 185259 Capscrew, Soc Bt Hd M5 x 0.8 x 16mm SS 4
51 172011 Nut, Hex Hd M5 x 0.80 4
52 174432 Capscrew, Soc Hd M5 x 0.8 x 10mm 3
Note 1: Effective with Tile Saw Serial Number 417841 (Built August 16, 2004):
Inner Flange, P/N 542190504 Replaced Inner Flange, P/N 185218, Spacer, P/N 185216, and Seal, P/N 185215 .
Outer Flange, P/N 542190504 can be used for units before Serial Number 417841, but Inner Flange (185218), Spacer (185216), and
Seal (185215) must be removed and discarded.