Electrolux TM-75 - Manual (Page 11)

11
3. Machine Set-Up
Follow all of the assembly and
installation instructions completely
before connecting this saw to a power
source.
UNPACKING
(Fig’s. 1, 2 & 3)
Carefully open the container and remove all the saw
components and packing materials. Be certain you
have checked each item with the checklist below
before discarding the container or the packing
materials. The contents are as follows:
1. Operator’s Manual 6. Cutting Guides (4)
2. Durable Water Tray 7. Water Pump w/ Hose
3. Saw Frame w/Cart 8. Blade - 8” [200 mm]
4. Power Head
9. Misc. Tools & Hardware
5. Blade Guard
NOTE: IF ANY OF THE PARTS ARE MISSING OR
DAMAGED PLEASE CONTACT YOUR FELKER
CUSTOMER SERVICE FOR INSTRUCTIONS.
CALL 1-800-365-4003
ASSEMBLY
•
Assembly Tools required:
- four wrenches supplied (2 allen type)
•
Place saw frame with cart into water tray. (Fig 4)
•
Feed the powerhead assembly onto the arm of the
saw frame through the opening in the back of the
powerhead. (Fig 5)
•
Allign the three holes in the powerhead with the
three threaded holes in the saw frame arm and
install the M5 x 10mm capscrews and lock
washers. (Fig 6)
• Loosely Install the M6 x 40mm capscrew and
washers at the rear of the saw frame. Insert just
enough brass spacers to fill any gap between the
saw frame and the powerhead, and then fully
tighten the capscrew. Not using spacers can
adversely affect allignment. (Fig 7)
•
Install blade guard onto the powerhead with
supplied knob. (Fig 8)
WATER PUMP INSTALLATION
•
Remove the water pump from its packaging and
check it to be sure it is not cracked or damaged in
any way.
• Route the 8mm plastic tubing as shown. (Fig 9)
• Attach the ends of the 8mm plastic tubing to the
blade guard and to the water pump. (Fig 10 & 11)
•
Place the water pump in the rear of the water tray
and set in place using the mounting bracket as
shown. (Fig 12)
• Keep the power cord out of the water and plug into
the motor pigtail three-pronged outlet. (Fig 16)
WATER PUMP SAFETY GUIDELINES AND
MAINTENANCE.
Always plug the saw power cord into a
GFCI outlet when using. If a GFCI type
outlet is not available, use a plug-in type
GFCI plugged into a properly grounded
outlet. Do not use any temporary plug
adapters.
• The water pump is equipped with a ground
electrical plug, to reduce the risk of possible
shock. Be sure to connect to a properly grounded
type receptacle.
•
Never pick the water pump up out of the water
when it is plugged in.
• DO NOT EVER use the water pump to pump
anything but water.
• Never service the pump when it is still plugged in.
•
Never let the pump operate dry. It is self-cooled
by pumping water. Dry use will cause the pump to
fail.
• Maintain regularly and clean out debris from intake
screen.
• Check the power cord for nicks or frays and never
try to alter the power cord in any way.
FITTING OR CHANGING THE BLADE
BLADE INSTALLATION AND REMOVAL
(Fig 13-15)
• Turn motor switch off.
• Disconnect power cord.
• Carefully raise the blade guard to its highest
position and tighten the adjustment knob on the
rear support, so as to put firmly in place.
•
Then remove the blade shaft nut and the outer
flange. (Fig 13) Use the 5mm allen wrench to hold
the shaft and the box end wrench to turn the nut
counter-clockwise. (Fig 15)
•
Place blade onto the shaft, pushing it up against
the inner flange. Make sure the blade is mounted
with the directional arrow pointing counter-
clockwise. (Fig 14)
•
Next replace the outer flange and shaft-nut and
tighten down. (Fig 14, 15) Do not over-tighten.
• Next lower the blade guard back into position and
tighten the knob.
Pay attention to the direction of rotation
shown by the arrow on one side of the
Blade (rotation in the opposite direction
to the tightening of the nut). Blade should
rotate counter-clockwise when facing the
bladeshaft nut.