Extron electronic TP R BNC A User Manual
Page 11
TP Receivers • Installation and Operation
TP Receivers • Installation and Operation
Installation and Operation, cont’d
2-8
TP R 15HD A only
— For optional rack mounting, mount the
receiver on a VersaTools 19" 1U Rack Shelf (Extron part
#60-190-20) (figure 2-4). The TP R 15HD A mounts in one of
four locations on the rack.
(2) 4-40 x 3/16" screws
Use 2 Mounting Holes on
Opposite Corners
VersaTools Rack Shelf
1/4 Rack Width False Front
Face Plate
TP
R 1
5H
D A
RG
B
PE
AK
IN
G
LE
VE
L
TP
R 1
5H
D A
RG
B
PE
AK
IN
G
LE
VE
L
TP
R 1
5H
D A
RG
B
PE
AK
IN
G
LE
VE
L
Figure 2-4 — VersaTools rack mounting the TP R 15HD A
1
.
If feet were previously installed on the bottom of the
receiver, remove them.
2
.
Mount the receiver on the rack shelf, using two 4-40 x 3/16
screws in opposite (diagonal) corners to secure the receiver
to the shelf.
3
.
Install blank panel(s) (included in the 1U universal and
VersaTools rack kits, optional for the 1U basic rack kit) or
other unit(s) to the rack shelf.
Only the TP R 15HD A and products in the Extron
VersaTools line can be mounted on a VersaTools shelf.
Any 1U rack-mountable Extron product can be mounted
on the standard shelf.
Furniture mounting
All of the receiver models can be mounted under furniture such
as a table or podium surface using the appropriate optional
mounting bracket, Extron’s Mini Under-Desk Mounting Kit
(part #70-212-01) (TP R 15 HD A) or Under-Desk Mounting Kit
(part #70-077-01) (all other models).
All models except the TP R 15HD A can be mounted through a
table or podium using Extron’s Through-Desk Mounting Kit
(part #70-077-02). Furniture mount the receiver as follows:
1
.
Attach the mounting brackets to the receiver with the
machine screws provided (figure 2-5).
Extron
TP R BNC A
Extron
TP R BNC A
Extron
TP R 15HDA
RGB INPUT
RGB OUTPUT
R
G
B
H/HV
V
A
AUDIO
L
R
B
SOG
C SYNC
PO
W
ER
15V
.5
A D
C
L
R
RG
B
IN
PU
T
RG
B
OU
TP
UT
R
G
B
H/
HV
V
A
AU
DI
O
L
R
B
SOG
C SY
NC
PO
W
ER
15V
.5
A D
C
L
R
Through-desk
Mounted
Under-desk
Mounted
Under-desk
Mounted
TP R 15HD A
RG
B
PE
AK
IN
G
LE
VE
L
Figure 2-5 — Under-desk or through-desk mounting
2
.
For through-surface mounting (all except TP R 15HD A)
,
cut the proper sized hole in the mounting surface.
3
.
Hold the receiver with the attached brackets against the
underside of the table or other furniture. Mark the
location of the screw holes of the bracket on the mounting
surface.
4
.
Drill 3/32” (2 mm) diameter pilot holes, 1/4” (6.3 mm)
deep in the mounting surface at the marked screw
locations.
2-9