Silvercrest 37702 - Manual (Page 19)

English 19
몇
Warning
Hot steam iron and hot steam escaping!Point
out to other people the possible risk of being
scalded or burned. Never direct the steam jet at
people or animals (risk of scalding). Do not touch
any electrical leads or combustible objects with
the hot steam iron.
Î Firmly insert the steam plug (H5) into the ap-
pliance connector (A1). The locks of the
steam plug must lock into the cover of the
appliance connector.
All fabrics can be steam ironed. Delicate imprints
or fabrics should be ironed on the reverse or ac-
cording to the manufacturer’s specifications.
Î Insert the mains plug (A7) into a socket.
Both indicator lamps (A2/A3) must illumi-
nate.
Î Adjust the temperature control (H2) of the
steam iron within the notched range (•••/
MAX).
Î Once the indicator lamp (H1) on the steam
iron has switched itself off, the steam iron is
ready for use.
Note:The sole plate must be hot to prevent
the steam from condensing on the sole plate
and dripping onto the garment to be ironed.
Î Press the switch (H3) on the iron.
– Steaming at intervals: Press the switch to
the front. A steam burst is emitted while the
switch is being pressed.
– Continuous steaming: Press the switch to
the back. The switch locks and steam is con-
tinuously emitted. To release, press the
switch to the front.
Î Direct the first burst of steam at a separate
piece of cloth until the steam is emitted even-
ly.
Î You can hold the iron in an upright position
to apply steam to curtains, dresses, etc.
Note:Even if you iron without steam, there must
be water in the boiler.
Î Adjust the temperature control (H2) of the
steam iron according to the garment you
want to iron.

Danger
Always disconnect the mains plug (A7) and allow
the steam cleaner to cool down before perform-
ing any maintenance work.
Rinse the steam cleaner boiler at the latest after
5 boiler fillings.
Î Fill the boiler with water and shake it strong-
ly. This dissolves lime scaling residing on the
boiler bottom.
Î Empty water out.
Note: If you always use usual commercial dis-
tilled water it is not necessary to descale the boil-
er.
As limescale builds up on the boiler walls, we
recommend to descale the boiler in the following
intervals (RF=reservoir fillings):
Note: Please contact your Conservancy Board
or the local water supply company to inquire
about the hardness of your water.
Î Disconnect the mains plug (A7) from the
socket.
Î Completely empty the steam boiler.
몇
Warning
Use commercial decalcifier for decalcifying the
unit.
Caution
Use caution when filling and emptying the steam
cleaner. The descaling solution can have an ag-
gressive effect on delicate surfaces.
Î Pour the descaling solution into the boiler
and allow it to react for approximately 8
hours.
몇
Warning
Do not screw the safety cap (A4) on the appli-
ance during the decalcifying.
Do not use the steam cleaner as long as there is
decalcifying agent in the boiler.
Î Empty the descaling solution after 8 hours. A
small amount of the solution will remain in
the boiler. Therefore, you should rinse the
Steam iron (H1)
Steam ironing
Dry ironing
• Synthetics
•• Wool, silk
••• Cotton, linen
Maintenance and care
Rinsing the boiler
Descaling the boiler
Degree of hardness ° dH mmol/l RF
I soft 0- 7 0-1,3 55
II medium 7-14 1,3-2,5 45
III hard 14-21 2,5-3,8 35
IV very hard >21 >3,8 25