Euro-Pro EP908H - Manual (Page 8)

Fig. 2
Fig. 3
OPERATING INSTRUCTIONS
100% white terry cloth towel can be fitted
on this brush, so as to absorb the dirt and
protect delicate surfaces.
Important: Please note that bristles may
break through thin towels. To cut and make
your own towels, we recommend that you
use one (1) towel 8” x 17” folded in half or
two (2) towels 4” x 17” laid one on top of
the other be used. This will ensure that the
brush bristles do not break through and
that the towels will be sufficiently absorbent
and retain as much dirt as possible.
Very Important : When installing the
towels to the floor brush, ensure that the
towels do not cover the front and the back
of the brush. (See Fig. 9)
Attaching a Towel to the Floor
Brush
4. Fold the other side of the towel as
shown in Fig. 7.
Fig. 7
Fig. 6
3. Fold the towel as shown in Fig. 6.
2. Place the brush on top of the towel.
Fig. 8
Fig. 9
Fig. 5
5. Place the corner under the cloth
holder as shown in Fig. 8.
OPERATING INSTRUCTIONS
Refilling Your Steam Cleaner
With Water
Step 1: Disconnect electrical power cord
from wall outlet.
Step 2: Depress and hold the hand grip
steam trigger to ensure that any
remaining pressure in the boiler
has been released.
Step 3: Carefully loosen the safety/filler
cap by turning counter clockwise.
Any residual steam will be
released below the safety/filler
cap if the tank has not been
completely vented. When the
hissing stops and the last of the
steam has been released,
remove the filler cap. Allow unit
to cool down.
CAUTION: Allow unit to cool for 15
minutes before refilling. If the steam
cleaner is still hot, there is a risk that
water will squirt back during filling and
cause scalding. Extreme care should
be taken when refilling the unit. Use
caution when opening the safety/filler
cap as cap may become hot during use
and escaping steam can cause
scalding.
Step 4: Allow the steam cleaner to cool
for 15 minutes before re-filling
with water.
Step 5: Refill water tank with water using
the filling funnel.
Step 6: Firmly screw the safety/filler cap
back onto the unit by turning
clockwise.
Step 7: Connect power cord to the wall
outlet.
NOTE: Fit floor brush with the angle
adapter on to the extension
tube.
Step 2: If the angle adapter is not
attached to the floor brush,
hold the brush with its bristles
up in your left hand. With the
angle adapter pointing
downward, insert it into the
hole in the back of the brush,
then turn the floor brush 180°.
Step 3: Insert the electrical power cord
into the wall outlet. Heating
time is approximately 8-10
minutes with cold water. Filling
the steam generator with hot
water will shorten the heat up
time.
Note: If you require continuous steam,
depress the trigger and engage the
trigger lock. (Fig. 2)
1. Prepare white terry cloth towel:
size 8” x 17” folded in half or place one
on top of another to have two layers.
(Fig. 5)
To clean the floor brush after you have
finished using:
1. Lift the front clip on the floor
brush (Fig. 4) and remove the brush.
2. Rinse the bristle brush and the
diffuser housing under warm water.
3. Replace bristle brush onto the diffuser
housing.
Fig. 4
Cleaning the Floor Brush
6. Place the towel around the brush,
and repeat folding the towel as shown
in Fig. 9. When folding the towel,
leave some slack. Do not pull tightly
around the brush, leave some
looseness.
Using Your Steam Cleaner with
Floor Brush
Step 1: Connect one of the extension
tubes to the hand grip on the
flexible steam hose. To
attach the extension tubes
one onto the other or
onto the hand grip, press the
locking button ensuring that it
fits into the hole. (Fig. 2, Fig. 3)
To disconnect, repeat the
operation by pressing the locking
button and pulling the two
sections apart.
6
7