Livarno Z31358-BS User Manual

Page 2

GB / IE

Improper disposal of recharge-

able batteries can damage the

environment!

Rechargeable batteries must not be disposed of

with the household refuse. They may contain toxic

heavy metals and require to be handled as special

waste. The chemical symbols of heavy metals are:

Cd = cadmium, Hg = mercury, Pb = lead.

EMC

Contact your local refuse disposal authority for

more details of how to dispose of your worn-out

product.

To help protect the environment,

please dispose of the product properly

when it has reached the end of its use-

ful life and not in the household waste.

Information on collection points and

their opening hours can be obtained

from your local authority.

Defective or exhausted rechargeable batteries

must be recycled in accordance with Directive

2006 / 66 / EC. Return the battery and / or the

device through the appropriate collection facilities.

Maintenance and cleaning

The product requires no maintenance. The LEDs

cannot be replaced.

Switch off and disconnect the product from

the power supply before you clean it.

Never immerse the product in water or other

liquids.

Do not use corrosive cleaning agents.

Clean the product regularly with a dry, fluff-

free cloth. Use a slightly moist cloth to remove

any stubborn dirt.

Disposal

The packaging is made entirely of

recyclable materials, which you may

dispose of at local recycling facilities.

Fault

Possible causes and cures

Indicator

LED

does not

illuminate

When connected to a

cigarette lighter socket:

- Is the cigarette lighter socket

supplied with power? Some

cigarette lighter sockets only

supply power with the ignition

switched on.

- Check the fuse in the vehicle.

Charging

takes a

very long

time

When connected to a

cigarette lighter socket:

- Vehicle battery too weak?

IAN 78535

OWIM GmbH & Co. KG

Stiftsbergstraße 1

D-74167 Neckarsulm

Model-No.: Z31358-BS

Version: 09 / 2012

GB / IE

Set the ON / OFF switch

to position I to

switch on the LED work lamp.

Set the ON / OFF switch

to position 0 to

switch off the LED work lamp.

Troubleshooting

Fault

Possible causes and cures

functions

- Mains adapter

or car adapter

is not fully inserted.

Use

CAUTION – RISK OF ACCIDENT! If at

all possible, do not use the LED work lamp in a

moving vehicle. If the LED work lamp is used in a

vehicle, it must not be allowed to endanger the

safety of the driver or passengers. Always store

and secure the LED work lamp in such a way that

there is no risk of injury from or damage to the

product, even during full braking.

Note: You can secure the LED work lamp in

place using the hook

Using the LED work lamp

disconnected from a power

supply

Fully charge the LED work lamp, as described in

the section on “Charging the LED work lamp”.

GB / IE

are permanently installed in the handle of the LED

work lamp.

Note: Charge the LED work lamp for approxi-

mately 12 hours before first use.

Note: Charge the LED work lamp at least once

a month, if it is to remain unused for an extended

period of time.

Note: If the LED work lamp has not been

charged for an extended period of time

(approx. 2 months), you could find that the

integral rechargeable batteries have entered a

dormant state. Charge and discharge the LED

work lamp a number of times in succession to

reactivate the integral rechargeable batteries.

Switch off the LED work lamp during the

charging process (set the ON / OFF switch

to position 0).

Remove the rubber protection cap from the

bottom of the LED work lamp.

Insert the power output connection plug of

the mains adapter

or the car adapter

into the power input connection socket

the handle of the LED work lamp.

Note: During charging from a cigarette lighter

socket, ensure that the plug is always completely

inserted into the cigarette lighter socket of the

vehicle. Failure to observe this advice may result

in risk of fire from overheating.

Insert the mains adapter

into a mains

socket or the car adapter

into the ciga-

rette lighter socket of your vehicle.

Note: The product has an overcharging

protection system. Nevertheless, you should

disconnect the LED work lamp from the mains

once the charging process is complete.

Note: The indicator LED

illuminates red

during the charging process. When the

charging process is complete, the indicator

LED

illuminates green. When the indicator

LED

illuminates green, pull the mains

adapter

out of the mains socket or the car

adapter

out of the cigarette lighter socket.

Disconnect the adapter from the LED work

lamp to prevent the batteries from discharg-

ing themselves.

Place the rubber protection cap back on the

power input connection socket

before you

start to use the LED work lamp again. Other-

wise water could enter the power input con-

nection socket

if the LED work lamp is

used outdoors.

78535_GB_IE.indd 2

10/11/2012 12:43:33 PM