Initial use, Maintenance, cleaning and care, Changing the water – Livarno Z30591B-BS User Manual
Page 25: Cleaning and care
25
GB/MT
Assembly and Initial Use / Maintenance, Cleaning and Care
j
Make sure that the rubber seal
2
completely
covers the hole, otherwise the water could leak
from the glass bowl
3
.
Note: You can moisten the rubber seal
2
so
that it slides more easily into the hole.
j
Take the mist generator
8
out of the glass
bowl
3
and place distance piece A
10
with
the suction cups facing downwards in the centre
of the glass bowl
3
. Press distance piece A
10
carefully against the bottom of the glass bowl
3
, so that the suction cups can adhere to it.
j
Place the mist generator
8
in distance
piece A
10
.
j
Insert distance piece B
12
into the connection
opening
11
of distance piece A
10
. Place the
rubber ring
13
on distance piece B
12
.
j
Please ensure that the mains lead
4
does not
lie across the mist generator
8
, as otherwise
no mist can be generated. In this case pull a
small section of the mains lead
4
through the
rubber seal
2
.
j
Fill the glass bowl
3
with approx.1000 ml of
water.
Note: Fill the glass bowl
3
up to the Max.
mark
7
only.
Note: The best result is obtained if the water
is slightly above the water level sensor
9
.
j
Place the glass cover
1
on the rubber ring
13
.
Note: The mist generator
8
switches off
automatically if the water level falls below the
water level sensor
9
.
j
In addition, a red LED light bulb will light up on
the water level sensor
9
when the water level
falls below the water level sensor
9
.
Note: Do not use fragrance oil.
Q
Initial Use
j
Connect the connection plug
5
to the adapter
plug
16
and insert the mains adapter
15
into
a socket (230 – 240 V ~, 50 Hz).
Note: Please ensure that the mains adapter
15
is located outside of the mist that is generated.
j
The mist generator
8
begins to generate a fine
spray of water which looks like smoke. The LEDs
17
light up and automatically change their colour.
j
If the tabletop mister is only generating water
spray or no mist will be produced, the water is
probably dirty. It should then be replaced (see
“Changing the Water”).
j
Turn the tabletop mister off by removing the
mains adapter
15
from the socket.
Q
Maintenance, Cleaning and Care
WArNING!
DANGEr OF DEAtH FrOM
ELECtrIC SHOCK! Always remove the mains
adapter
15
from the socket before performing any
work on the product.
Q
Changing the Water
j
Change the water at least once a week. This
prevents the formation of algae.
j
Pour out the water and allow the tabletop mister
to dry completely if you are not going to use it
for a prolonged period.
j
Dirty water impairs / prevents the correct func-
tioning of the mist generator
8
. If the device is
only generating water spray or if the quantity
of mist is less than usual, replace the water in
the glass bowl
3
.
j
Remove the mains adapter
15
from the socket.
Disconnect the connection plug
5
and
adapter plug
16
.
m CAUtION! It is essential to hold the glass
bowl
3
over a wash basin. Water might
drain / spill out of the glass bowl
3
.
j
Remove the mist generator
8
and distance
piece A
10
from the glass bowl
3
. Pull the
rubber seal
2
out of the small hole in the
glass bowl
3
.
j
Pour out the water and clean the glass bowl
3
.
j
Reassemble the tabletop mister as described
under “Assembly and Initial Use”.
Q
Cleaning and Care
j
Use a dry, lint-free cloth for external cleaning
and care.