Caution, Wiring/connection chart, Performance match – Electro-Voice Sound Reinforcement System Xi-1123A/106F User Manual
Page 4
U.S.A. and Canada only. For customer orders, contact Customer Service at:
800/392-3497 Fax: 800/955-6831
Europe, Africa, and Middle East only. For customer orders, contact Customer Service at:
+ 49 9421-706 0 Fax: + 49 9421-706 265
Other International locations. For customer orders, contact Customer Service at:
+ 1 952 884-4051 Fax: + 1 952 736-4212
For warranty repair or service information, contact the Service Repair department at:
800/685-2606
For technical assistance, contact Technical Support at: 866/78AUDIO
Specifications subject to change without notice.
12000 Portland Avenue South, Burnsville, MN 55337
Phone: 952/884-4051, Fax: 952/884-0043
www.electrovoice.com
© Telex Communications, Inc. 5/2004
Part Number 38110-274 Rev. A
Architectural & Engineering Specs:
Dimension Drawings:
Xi-1123A/106F Part Numbers
•
1149-3415 - Black
•
1149-3404 - White
The loudspeaker system shall be a three-way tri-amp or bi-amp system. The system shall have an 12-inch, low-frequency loudspeaker
with a nominal impedance of 8 ohms and a 2.5-inch voice coil. The low-frequency loudspeaker shall have a power handling capacity
of 300 watts for 8 hours (as per ANSI/EIA RS-426 A & AES 2-1984). The mid-bass loudspeaker shall be a fully horn loaded, 10-inch driver
with a 2.5-inch voice coil and a nominal impedance of 8 ohms. The mid-bass driver shall have a power-handling capacity of 300 watts
for 8 hours (as per ANSI/EIA RS-426 A). The high-frequency section shall employ a compression driver capable of handling 75 watts,
1,760- to 20,000-Hz when pink noise of a 6-dB crest factor is applied for 2 hours (as per AES 2-1984 and ANSI S4.26-1984 standards).
The loudspeaker shall be constructed of 18-mm, 13-ply birch and shall be trapezoidal in shape. The wedge angle shall be 18-degrees.
The grille shall be constructed from 16 GA powder-coated steel backed by acoustically transparent fabric. The system shall be capable
of very-high level operation with a band width of 53 to 19,000 Hz. The system dimensions shall be 458 mm (18.05 inches) wide by 801
mm (31.54 inches) high by 473 mm (18.64 inches) deep. The system shall employ flying hardware of a “track” style and have two tracks
on the enclosure top and two tracks on the enclosure bottom. Net weight shall be 52.2 kg (115 lbs).
The loudspeaker shall be the Electro-Voice
®
Xi-1123A/106F.
This Xi Loudspeaker should be suspended overhead only in accordance with the procedures and limitations specified in the
X-Array Xi Install Flying Manual and possible manual update notices. This system should be suspended with certified rigging
hardware by an authorized rigging professional and in compliance with local, state, and federal overhead suspension ordinances.
CAUTION
Performance Match
• P3000 (RL)
• CPS 2.8
• Dx38
• P1200 (RL)
• CPS 2.11
Wiring/Connection Chart:
p
m
a
i
r
T
p
m
a
i
B
:
F
L
n
I
1
s
n
i
P
t
u
O
2
s
n
i
P
:
F
L
n
I
1
s
n
i
P
t
u
O
2
s
n
i
P
:
B
M
n
I
3
s
n
i
P
t
u
O
3
s
n
i
P
:
F
H
/
B
M
n
I
3
s
n
i
P
t
u
O
3
s
n
i
P
:
F
H
n
I
4
s
n
i
P
t
u
O
4
s
n
i
P
h
g
u
o
r
h
T
s
s
a
P
4
s
n
i
P
t
u
O
1
s
n
i
P
o
t
d
e
t
c
e
n
n
o
C
n
I
2
s
n
i
P
Triamp to Biamp - Switch 4-Pin
Connector on inside of Input Panel.