Livarno 103756-14-01-BS/ 103756-14-02-BS User Manual

Page 2

OF ELECTRIC SHOCK!

DANGER OF DAMAGE

TO PROPERTY!

DANGER OF INJURY!

Ensure that you do not strike

electrical cables, gas or

water pipes when you are

drilling into the wall. If

necessary, check the wall

using a suitable detector

before you drill.

RISK OF

INJURY FROM

BURNS! Ensure

the lamp has been switched

off and allowed to cool

before you touch it. In this

way you will avoid the

danger of burns. Bulbs give

off a lot of heat around the

top of the lamp.

Do not use this light for

dimmers or electronic

switches. It is not suitable

for these purposes.

Working safely

Install the lamp so that it is

protected from moisture,

wind and dirt.

Make careful preparations

for the assembly and take

sufficient time. Clearly lay

out all components and any

additional tools or materials

that might be required so

that they are readily to

hand.

Remain alert at all times

and always watch what you

are doing. Always proceed

with caution and do not

assemble the lamp if you

cannot concentrate or feel

unwell.

GB/IE

purchase. This warranty

becomes void if the device has

been damaged or improperly

used or maintained.

The warranty applies to faults in

material or manufacture. This

warranty does not cover

product parts subject to normal

wear, thus possibly considered

consumables (e.g. batteries) or

for damage to fragile parts, e.g.

switches, rechargeable batteries

or glass parts.

environmentally-friendly

materials. They can be disposed

of at your local recycling facility.

The symbol of the

wheelie bin with the

line through it means

that, in the European Union, the

product has to be disposed of in

a separate refuse collection.

This applies to the product and

to all components bearing this

symbol. Products marked in this

way may not be disposed of

along with normal domestic

waste but have to be handed in

at a recycling collection point

for electrical and electronic

appliances. Recycling

helps to reduce the consumption

of raw materials and to ease the

burden on the environment.

Warranty

The device has been

manufactured to strict quality

guidelines and meticulously

examined before delivery. In the

event of product defects you

have legal rights against the

retailer of this product. Your

legal rights are not limited in

any way by our warranty

detailed below.

The warranty for this device is 3

years from the date of purchase.

Should this device show any

fault in materials or manufacture

within three years from the date

of purchase, we will repair or

replace it - at our choice - free

of charge to you.

The warranty period begins on

the date of purchase. Please

keep the original sales receipt in

a safe location. This document is

required as your proof of

distance of approx. 15 cm

as described.

Remove the protective cap

by unscrewing the

screw. Connect the two

under-unit lights to the

socket

using the

extension lead

. Then

you only need one connec-

tion lead

for the power

supply.

CAUTION! First ensure

that all the under-unit lights

are connected by an

extension lead

before

you insert the mains lead

into the mains socket.

Maintenance and

Cleaning

Allow the lamp to cool down

completely.

DANGER

TO LIFE FROM ELECTRIC

SHOCK! Before carrying

out any tasks on the lamp,

switch off the electrical

circuit at the circuit breaker

box or remove the fuse from

the fuse box.

CAUTION! Do not use

solvents, petrol etc.

DANGER

TO LIFE FROM ELECTRIC

SHOCK! For reasons of

electrical safety, the light

must never be cleaned with

water or other fluids or be

immersed in water. When

cleaning, only use a dry,

lint-free cloth.

Disposal

The packaging and

ancillary packing

consist entirely of

light is now ready for

operation.

Mounting model

103756-14-02-BS

on a wall

Measure up the wall or

mounting surface for drilling

the holes. Use a spirit level

to improve accuracy.

Mark the two mounting

holes a distance of approx.

432 mm apart.

Now drill the mounting

holes (ø approx. 6 mm,

depth approx. 30 mm).

CAUTION! Make sure that

you do not damage any

electrical cables during this

operation.

Insert the supplied dowels

into the drilled holes.

Insert the supplied screws

into the dowels and

tighten them. Let them

project a distance of about

1.3 mm from the wall or

mounting surface.

Attach the light to the

screws

using the

appropriate wall mounting

holes

Plug the connection cable

with mains plug

into the

socket for the connection

cable

Plug the connection cable

with mains plug

into the

mains socket. Your light is

now ready for operation.

Extensions

Note: Ensure that no more

than 3 under-unit lights of the

same type (103756-14-02-BS)

are connected together in

series. Install each

additional light at a

Mark where you wish to

drill and pre-drill the holes.

Mark the distance of

533 mm for the two fixing

holes. Drill the holes: ø

approx. 2 mm, approx.

10 mm deep.

Note: The supplied screws

are for standard installation

under wall cabinets and are

not suitable for every type

of wall. If installing on

concrete walls, for example,

you will need to use special

dowels and screws.

Information on suitable

installation material can be

obtained from specialist

stores.

First screw only one of the

mounting rails

in the pre-

drilled positions with the

supplied screws

Place the under cabinet

light flat on the mounting

surface and push it onto the

mounting rail

up to the

stop in the slot

(see Fig. C).

Push the second mounting

rail

into the slot

the under cabinet light so

that the drilled hole is

visible. Tighten the screw in

this position (see Fig. D).

Now push the under

cabinet light a little to the

right. Both mounting rails

should now be firmly

positioned (see Fig. E).

Check that the under

cabinet light is fitted

securely.

Plug the connecting lead

into the socket

Plug the mains plug of the

connecting lead

into a

socket. Your under cabinet

Installation and

operation

Installing light

103756-14-01-BS

Measure the space for

installation of the light. Use

a spirit level to position it

correctly.

Mark the position of the drill

holes

in the under

cabinet light.

Mark the two mounting

holes at a distance of

362 mm apart.

Drill the holes, ø approx.

2 mm, depth approx.

10 mm.

Position the under cabinet

light according to the drilled

holes and tighten the

screws

Plug the connecting lead

into the socket

Plug the mains plug of the

connecting lead

into a

socket. Your under cabinet

light is now ready for

operation.

Note: Only use the lamp

with the mains adapter it

was delivered with

(LPS03-120-0250-3).

Damage due to use of a

different adapter is not

covered by the guarantee.

Installing light

103756-14-02-BS

Use the mounting rails

(see also Fig. B) and the

screws

for under cabinet

installation.

Measure the space for

installation of the light. Use

a spirit level to position it

correctly.

IAN 103756

OWIM GmbH & Co. KG

Stiftsbergstraße 1

D-74167 Neckarsulm

Model no.: 103756-14-01-BS /

103756-14-02-BS

Version: 10 / 2014