Sealey ER1700PD - Manual (Page 2)

 Remove ill fitting clothing. Remove ties, watches, rings, and other loose jewellery and tie back long hair.
 Keep children and unauthorised persons away from the working area.
 Secure non-stable work piece with a clamp, vice or other adequate holding device.
 Remove adjusting keys and wrenches from the machine and its vicinity before turning it on.
 DO NOT use equipment for any purpose other than that for which it is designed.
 DO NOT operate the polisher if any parts are damaged or missing as this may cause failure or possible personal injury.
 WARNING! DO NOT sand any materials containing asbestos.
 DO NOT switch the polisher on whilst the head is in contact with the work piece and avoid unintentional starting.
 DO NOT get the polisher wet or use in damp or wet locations or areas where there is condensation.
 DO NOT allow untrained persons to operate the polisher.
 DO NOT operate the polisher when you are tired, under the influence of alcohol, drugs or intoxicating medication.
 DO NOT use the polisher where there are flammable liquids, solids or gases such as paint solvents, etc.
 DO NOT leave the polisher operating unattended.
 DO NOT carry the polisher with your finger on the power switch.
 DO NOT pull the cord to remove the plug from the power supply.
 Use a qualified person to lubricate and maintain the polisher.
 When not in use unplug from the mains power supply and store in a safe, dry, childproof area.
LEAD PAINT WARNING! Paint once contained lead as a traditional ingredient. Contact with the dust from the removal of such paint is toxic
and must therefore be avoided. The following action must be taken before using machine as a sander:
1. User must determine potential hazard relating to age of paint to be removed. (Modern paints do not have lead content).
2. DANGER! Keep all persons and pets away from the working area. The following are particularly vulnerable to the effects of lead
paint dust: pregnant women, babies and children.
3. Wear appropriate Personal Protective Equipment. A full range of Personal Protective Equipment is available from your Sealey Dealer.
4. Take adequate measures to contain paint dust, flakes and scrapings. Wear safety equipment, as in (3) above and thoroughly clean
all areas when task is complete.
5. Ensure the paint waste is disposed of in sealed bags or containers according to local regulations.
3. SPECIFICATIONS
2. INTRODUCTION
4. ASSEMBLY
 WARNING! Ensure unit is not plugged into mains before
attempting any assembly.
4.1. Attaching the side handle.
4.1.1. Traditional Handle (fig.1):
Attach the side handle to either side by screwing into the
desired fixing hole in the head.
4.1.2. Over the Top Handle (fig.2):
Slide both sides of the handle over the fixing holes (fig.3)
and secure with the hex nuts supplied.
4.2. Attaching the backing pad.
4.2.1. With the machine disconnected from the electrical supply,
spin the backing pad onto the spindle until resistance from
the motor is felt. The disc will tighten itself sufficiently when in
use.
4.3. Removing the backing pad.
With the machine disconnected from the electrical supply,
depress the spindle lock button (fig.5). Turn the backing pad
by hand until the spindle lock is felt to engage. Turn the
backing pad clockwise (viewed from above) to release and
remove.
4.4. Attaching the lambswool bonnet.
Turn the edge of the bonnet back (fig.4), then place the backing
disc centrally on the `hook and loop fixing. When fixed, turn the
edge of the bonnet back over the edge of the backing pad.
Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ER1700PD
Pad Size:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ø180mm
Thread Size: . . . . . . . . . . . . . . . . . . . . . . . . .M14 x 2mm
No Load Speed: . . . . . . . . . . . . . . . . . . . . . . 0-3000rpm
Power: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1100W
Supply: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230V
Weight: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.5kg
Noise Power:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82dBA
Noise Pressure:. . . . . . . . . . . . . . . . . . . . . . . . . . . 71dBA
Vibration: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.36m/s²
Uncertainty: . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.68m/s²
Powerful 1100W motor enclosed in a lightweight housing. Maintains high torque levels at low speeds, ideal for polishing. Digital display for
variable speed control from 1000-3000rpm, stepping-up in 500rpm increments. Features a slide button on/off switch allowing for a smooth,
comfortable main handle grip. Spindle lock for fast and easy pad/foam head changes. Choice of two side handles:. traditional or over-the-top
style. Supplied in robust storage case.
fig.1
fig.2
fig.3
ER1700PD Issue:1 - 15/10/14 Original Language Version © Jack Sealey Limited