Sealey HS104K - Manual (Page 2)

Power Supply: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230V 9A
Power output: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2000W
temperature range (Step 1/2): . . . . . . . . . . . 80°C/80 - 600°C
Air Flow: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 480ltr/min
Fitted with variable electronic temperature control and lCD temperature display. two-speed air-flow control. Suitable for paint stripping, soft
soldering, removing sticky labels and defrosting frozen pipes. Double insulated and fitted with BS approved 3 pin safety plug. Supplied with
four nozzles, stripper, scraper handle and three scraper blades.
Fig.1
2.temperature Dial
1.on/off and
Airflow Control Switch
 DO NOT use the hot air gun in rain or in a wet environment, or in areas of high humidity and damp (i.e. bathrooms, steam rooms, etc.).
 DO NOT obstruct the hot airflow by blocking or covering the air outlet.
 DO NOT touch the nozzle during, or after, use as it becomes extremely hot.
 DO NOT leave the hot air gun running unattended. Always turn off the power supply.
 DO NOT use the hot air gun on a task it is not designed for.
 DO NOT use the hot air gun in combination with chemical strippers.
 DO NOT operate the hot air gun when you are tired or under the influence of alcohol, drugs or intoxicating medication.
 DANGER! DO NOT USE THE HOT AIR GUN AS A HAIR DRYER.
WARNING: The warnings, cautions and instructions discussed in this instruction manual cannot cover all possible conditions and
situations that may occur. It must be understood that common sense and caution are factors which cannot be built into this product,
but must be applied by the operator.
1.3. LEAD PAINT WARNING! Paint once contained lead as a traditional ingredient. Paint particles, resulting from the removal of such
paint, are toxic and ingestion/inhalation must, therefore, be avoided. the following action must be taken before using this tool:
1.3.1. the operator must determine potential hazard relating to age of paint to be removed (modern paints do not have lead content).
1.3.2. DANGER! Keep all persons and pets away from the work area. the following are particularly vulnerable to the effects of lead paint
dust: Expectant women, babies and children.
1.3.3. We recommend personal protection by using the following safety items: Paint Spray Respirator (Sealey ref. SSP1699), PE Coated
Hooded Coverall (Sealey ref. SSP267), Latex Gloves (Sealey ref. SSP24).
1.3.4. take adequate measures to contain the paint dust, flakes, and scrapings.
1.3.5. When task is complete continue to wear safety equipment as in 1.3.3. and thoroughly clean all areas. Ensure paint waste is disposed
of in sealed bags or containers.
2. INTRODUCTION
3. SPECIFICATION
4. OPERATION
4.1. Preparation.
4.1.1. Select and fit a suitable nozzle for the work area (if required).
4.1.2. Connect to the power supply, ensuring the on/off switch (Fig.1.1) is in the ‘0’ position.
4.1.3. Set the switch (Fig.1.1) to the required setting, position '1' (80°C) or position '2' (variable - 80 to 600°C). rotate the temperature dial to
the required temperature setting (Fig.1.2). It is best to start at a lower temperature and gradually increase it if necessary. Allow a
short period for the gun to reach the desired temperature, using the lCD display for reference.
NOTE: When new, the hot air gun may generate some smoke, this will decrease with use.
 WARNING! KEEP HANDS AWAY FROM THE IMMEDIATE NOZZLE AREA. IF LEAD PAINT IS BEING REMOVED
FOLLOW THE SAFETY INSTRUCTIONS. ALWAYS WEAR GLOVES AND EYE PROTECTION.
4.2. Paint and varnish removal.
the easy removal of paint and varnish requires practice. Follow these simple working techniques to achieve the required result.
NOTE: the hot air gun is designed to remove both oil and latex based paints and varnishes from surfaces. It will not remove stains
or primer coats that have impregnated the surface.
4.2.1. Always test on a small non-critical area first.
4.2.2. Select a shaped scraper suitable for the work area, and fix it securely to the scraper handle by tightening the nuts either side of it.
HS104K.V2 Issue: 2(l) - 23/03/15
Original Language Version © Jack Sealey limited