Sealey SD1000 - Manual (Page 3)

3.2.8. selection of hammer action / drilling. When using a masonry drill bit the hammer action
can be used to assist penetration into concrete, stone and masonry.
the hammer action selector is a large sliding ‘switch’ situated on top of the drill
(see fig.4). to select hammer action slide the selector to the left so that it is adjacent
to the hammer symbol moulded on the side of the case. to disable the hammer action
slide the switch in the other direction to be adjacent to the drill symbol moulded on the
other side of the casing.
3.3. drill Or TOOl biT FiTTiNG.
 WARNING! Unplug from the mains power supply before placing bit into chuck.
open or close the chuck jaws to a point where the opening is slightly larger than the drill or
tool bit to be used. raise the front of the drill slightly to stop the bit from falling out of the
chuck jaws. Insert the drill bit (A) into the chuck as far as it will go. Place the chuck key (9)
in one of the chuck holes and tighten the chuck securely (fig 3).
3.4. depTh sTOp GaUGe.
ensure the work piece has a flat surface and is wide enough for the gauge to butt up
against when the required depth has been reached. measure back from tip of the drill bit
to the point at which the drill must stop. release clamp/handle and extend the depth
gauge to the point at which you wish to stop the drill penetrating further and retighten the
handle/clamp. once drill has reached the correct depth the gauge will butt up against the
work piece and stop further inward progress.
fig.5
fig.3
 WARNING! Only change gear when the drill is not turning.
the required speed will depend on the material and task in hand. the following may be used
as a general guide.
a) low speeds are recommended for hard materials i.e. stone, ceramic, concrete, high
tensile steel and tasks such as starting holes without centre punch, driving screws, mixing
paint etc.
b) medium speeds are suitable for plastics and laminates.
c) High speeds recommended for soft materials such as wood, aluminium, copper, bronze
and brass.
 CaUTiON: DO NOT run your drill at low to medium speeds for extended periods of
time as this may cause drill to overheat.
To cool drill run it without a load for approximately 3 minutes at full speed.
3.2.7. direction of rotation. select either forward or reverse rotation using the slide mounted
above the trigger. (see fig.5) the slide moves from left to right. select reverse by
moving the slide to the  symbol. to select the forward direction move the slide to the
other side to be adjacent to the  symbol.
 CaUTiON: Do not change direction of rotation whilst the drill is running.
Original Language Version sd800.V3 & sd1000.V3 Issue no:1 13/02/14
fig.4
4. maiNTeNaNCe
4.1. Changing the drill chuck.
to remove the drill chuck open the chuck fully. locate the internal screw and undo turning the screw clockwise (left handed thread),
to stop the chuck from moving, grip the chuck, if tight the chuck key can be used to provide additional leverage. on the sd1000 the
chuck can be held in position with a spanner. to replace the chuck reverse the above process.
4.2. Cleaning
Keep the drill ventilation slots clean and free from obstructions. If available blow compressed air into the vents to clear any internal
dust (safety goggles must be warn when undertaking this process). Keep the outer case of the drill clean and free from grease.
dO NOT wash with water or use solvents or abrasives.
4.3. brushes
the brushes must be changed by an authorised sealey service agent. ,
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
impOrTaNT: no liability is accepted for incorrect use of this product.
WarraNTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
iNFOrmaTiON: for a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
01284 757500
01284 703534 [email protected]
sole UK distributor, sealey Group,
Kempson Way, suffolk Business Park ,
Bury st. edmunds, suffolk,
IP32 7Ar
www.sealey.co.uk
Web
email
environmental protection.
recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycling
centre and disposed of in a manner which is compatible with the environment.
Weee regulations.
dispose of this product at the end of its working life in compliance with the eu directive on Waste electrical and electronic equipment.
When the product is no longer required, it must be disposed of in an environmentally protective way. contact your local solid waste authority for
recycling information.
© Jack sealey limited