Sealey SD1000 - Manual (Page 2)

3. OperaTiNG iNsTrUCTiONs
mOdel: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .sd800.v3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . sd1000.v3
supply:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230V 50Hz . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230V 50Hz
motor Power: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 850W . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1050W
no load speed: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 - 3000rpm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 - 1100 / 0 - 3000rpm
chuck capacity: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13mm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13mm
Hammer Action: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0-48000bpm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 - 17600 / 0 - 48000bpm
drilling capacity - steel: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13mm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13mm
drilling capacity - Wood: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25mm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25mm
drilling capacity - masonry: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13mm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16mm
Weight: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2kg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4kg
sound Pressure level: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93dB(A) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .95dB(A)
sound Power level: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104dB(A) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .106dB(A)
Vibration level: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.73m/s 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.7m/s 2
uncertainty: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.36m/s 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.35m/s 2
2. iNTrOdUCTiON & speCiFiCaTiONs
3.1. prepariNG drill FOr Use.
3.1.1. ensure the drill is switched off and unplugged from the mains power supply.
3.1.2. Fitting the side handle. fit supplementary handle grip by placing the handle assembly over chuck head and onto the machine neck.
secure by rotating the handle clockwise until it is tight and the handle can no longer be moved. to ensure a good grip in all
circumstances the angle of the handle may be changed by rotating the handle grip anti-clockwise until the handle assemble is loose.
rotate the handle to the desired angle and retighten.
3.1.3 Fitting the depth gauge. to fit the depth gauge loosen the side handle and pass the gauge through the handle clamp to the required
depth. rotate the handle to the required angle. As the handle is tightened the depth gauge will also be gripped firmly.
3.2. drill CONTrOls
3.2.1. ON/OFF variable speed trigger. Your drill has a variable speed control on/off trigger, which increases the speed the more the trigger
is depressed.
3.2.2. Trigger lock. to lock ‘on’, depress the trigger, push in and hold the button then release the trigger. release the lock on button and
your drill will continue running accordingly.
3.2.3. to release the lock depress the trigger and release it.
3.2.4. Power failure. If you have the lock on feature engaged during use and your drill becomes disconnected from the power supply,
disengage the lock on feature immediately.
 WARNING! Before connecting your drill to power supply, ensure it is not in the lock on position as this may result in
damage and personal injury. Depress the trigger to ensure release. DO NOT use the lock on facility for jobs where your drill
may need to be stopped suddenly. ,
3.2.5. maximum speed setting control. the variable speed trigger has a small rotating knob incorporated into it, which can be used to
control the maximum speed of the drill. When the knob is set to the maximum or + setting the trigger can be fully depressed allowing
the drill to turn at its maximum speed. As the knob is turned towards the minimum or - setting the movement of the trigger is restricted
so that the drill will turn at a lower pre-set speed when the trigger is fully depressed. this facility is useful when working with materials
that should be drilled at a constant, lower speed.
3.2.6. Two speed gearbox (sd1000 only). the sd1000 also incorporates a 2 speed mechanical gearbox which used in conjunction with
the other speed controls adds additional versatility to this model. to select the lower speed turn the gear selector so that ‘1’ is
adjacent to the arrow on the casing. to select the higher speed turn the gear selector so that ‘2’ is adjacent to the arrow on the
casing. It may be necessary to rotate the chuck by hand slightly whilst using the gear selector in order to get the gears to mesh.
Original Language Version
sd800.V3 & sd1000.V3 Issue no:1 13/02/14
sd800.v3 sd1000.v3 fig.1 fig.2
sd800.v3
Professional 850W hammer drill with variable speed and reverse controls. suitable for driving and removing screws. Hammer action allows
up to 13mm capacity in masonry. features high quality chuck with soft grip handle and body for added comfort. supplied with adjustable side
handle, depth stop and 2mtr cable with Bs approved plug.
sd1000.v3
Professional heavy-duty 1050W hammer drill with variable speed and reverse controls. suitable for driving and removing screws. two speed
mechanical gearbox gives added versatility and hammer action allows up to 16mm capacity in masonry. features high quality chuck with soft
grip handle and body. supplied with adjustable side handle, depth stop and 2mtr cable with Bs approved plug, all in a carry-case with
accessories.
1 . . . . . trigger lock Button
2 . . . . . on/off trigger
3 . . . . . forward/reverse selector
4 . . . . . Variable speed control
5 . . . . . chuck
6 . . . . . drill/Impact selector
7 . . . . . side Handle
8 . . . . . depth Gauge
9 . . . . . chuck Key
10 . . . . High/low Gear selector
(sd1000.V3 only)
© Jack sealey limited