Electrolux ICON E30MO65GSS - Manual (Page 3)

30" Combination Installation –
Built-In Microwave/Single Wall Oven
High standards of quality at Electrolux Home Products, Inc. mean we are
constantly working to improve our products. We reserve the right to change
specifications or discontinue models without notice.
Electrolux Major Appliances, N.A.
USA • 250 Bobby Jones Expressway • Augusta, GA 30907 • 1-877-4electrolux (1-877-435-3287) • electroluxicon.com
CANADA • 5855 Terry Fox Way • Mississauga, ON L5V 3E4 • 1-800-265-8352 • electroluxicon.ca
MO_EW INST 01/09 © 2009 Electrolux Home Products, Inc. Printed in the U.S.A.
30" Combination Installation Specifications
• Always consult local and /or national electric codes.
(Refer to product-specific electrical specifications on this page.)
• Minimum 24"deep cutout dimension is critical for proper combination
installation, to ensure that each built-in product’s faceplate will fit
flush against cabinet front.
• Bases must be level and cabinet front must be square.
• Minimum 4-1/2" required distance from bottom of Wall Oven cutout
to floor, 31" suggested.
• Respect critical dimensions as noted for proper installation of built-In
products.
• Minimum 23-1/4" clearance needed for Wall Oven door depth
when open.
30" Built-In Convection Microwave Specifications
• Product Weight – 60 Lbs.
• Voltage Rating – 120V / 60 Hz / 15 Amps
• Connected Load (kW Rating) @ 120 Volts = 1.55 kW
(For use on adequately wired 120V, dedicated circuit having 2-wire
service with a separate ground wire. Appliance must be grounded
for safe operation.)
• Amps @ 120 Volts = 13 Amps
• Consult local building code in the event that cutout opening may
be required to be enclosed with sides, ceiling and rear partition.
• Full base of solid plywood or similar material required, capable of
supporting 100 Lbs.
• Minimum 3-1/8" clearance required from bottom of Built-In Microwave
cutout to top edge of Wall Oven’s faceplate, leaving a 2" visible gap
between both product faceplates.
30" Electric Single Wall Ovens Specifications
• Product Weights – (E30EW75GPS) 178 Lbs. / (E30EW75GSS) 175 Lbs.
• Single phase 3- or 4-wire cable, 120 / 240 or 120 / 208 Volt, 60 Hertz
AC only electrical supply with ground required on separate circuit fused
on both sides of line.
• Connected Load (kW Rating) @ 240 / 208 Volts = 4.0 / 3.0 kW
• Amps @ 240 / 208 Volts = 16.6 / 14.4 Amps
• Full oven base of solid plywood or similar material required, capable of
supporting 200 Lbs.
Note: For planning purposes only. Refer to Product Installation Guide
on the web at electroluxicon.com for detailed instructions.
For detailed product dimensions
and installation specifications, refer
to model-specific product page and
installation guide on web
* Minimum 3 1 / 8 "
clearance required
from bottom of
Built-In Microwave
cutout to top edge of
Wall Oven’s faceplate,
leaving a 2" visible
gap between both
product faceplates
** Critical dimension –
MUST be applied
30" Electric Single
Wall Oven Cutout
For models:
E30EW75GPS
E30EW75GSS
30" Built-In
Microwave Cutout
For model:
E30MO65GSS
24" min. 30" min.
3" max.
26 1 /
2
" min.
27" max.
28 1 /
2
" min.
28 7 / 8 " max.
Full plywood base
required to support
100 lbs.
28 1 /
2
" min.
29" max.
4"x 4" opening
to route armoured
cable
120V/60 Hz
grounded electrical
outlet should NOT
be located within
shaded area
19 7 /
8
" min.
20 3 /
8
" max.
24" min.**
(critical
dimension)
2" min.
31"
suggested
distance
4 1 /
2
"
min.
required
Bottom cutout
edge must be
finish cut
Full base required
to support 200 lbs.
Electrical junction
box location
2"
(visible
gap)*
5"
11 1 / 2 "