Electrolux ICON E30MO65GSS - Manual (Page 2)

Built-In Convection Microwave
E30MO65GSS designer series
High standards of quality at Electrolux Home Products, Inc. mean we are
constantly working to improve our products. We reserve the right to change
specifications or discontinue models without notice.
Electrolux Major Appliances, N.A.
USA • 250 Bobby Jones Expressway • Augusta, GA 30907 • 1-877-4electrolux (1-877-435-3287) • electroluxicon.com
CANADA • 5855 Terry Fox Way • Mississauga, ON L5V 3E4 • 1-800-265-8352 • electroluxicon.ca
E30MO65GSS 01/10 © 2010 Electrolux Home Products, Inc. Printed in the U.S.A.
30" Built-In Convection Microwave Specifications
• Product Weight – 60 Lbs.
• Voltage Rating – 120V / 60 Hz / 15 Amps
• Connected Load (kW Rating) @ 120 Volts = 1.55 kW
(For use on adequately wired 120V, dedicated circuit having 2-wire
service with a separate ground wire. Appliance must be grounded
for safe operation.)
• Amps @ 120 Volts = 13 Amps
• Always consult local and national electric codes.
• Allow 19" minimum clearance for 90° door swing.
• Built-In installation requires use of 30" Trim Kit (PN # E30MO65TMK)
which is supplied and includes Stainless Steel Faceplate, Exhaust
Duct Assembly and Bottom Duct Assembly – shipped in separate box.
• Minimum 20-1/8" deep oven cutout dimension is critical for proper
installation for oven and faceplate to fit flush against cabinet front.
• Full base of solid plywood or similar material required, capable of
supporting 100 Lbs.
• Base must be level and front of cabinet square for proper operation.
• Grounded outlet should NOT be located in shaded area, as indicated.
• Can NOT be installed above any gas wall oven.
• Built-In Convection Microwave can be built in alone or is approved to
be used in combination with any Electrolux ICON
® Electric Single
Wall Oven and / or Warmer Drawer. (Refer to model-specific Combination
Installation Specifications pages on web.)
• When used in combination with another Electrolux ICON ® built-in
product, a minimum clearance of 3-1/8" required from bottom of Built-In
Microwave cutout to top edge of companion product’s faceplate, leaving
a 2" visible gap between both product faceplates.
Note: For planning purposes only. Refer to Product Installation Guide
on the web at electroluxicon.com for detailed instructions.
30" min.
20 1 /
8
"
min.
19 7 / 8 "
min.
20 3 /
8
"
max.
Full plywood
base required
to support
100 lbs.
2"
min.
26 1 / 2 " min.
27" max.
2"
(visible
gap)*
30"
Allow at least
19" clearance for door
depth when open
21 23 /
32
"
24 5 /
8
"
20 29 /
32
"
Power
cord
location
(right
bottom
rear)
Exhaust Duct
Assembly
Faceplate
19 5 /
8
"
Bottom Duct Assembly
7 /
8
"
Bottom Duct Assembly
120V/60Hz
grounded outlet
Outlet should
NOT be located
within shaded
area
26 1 /
2
" 20 1 /
8
" min.
19 7 /
8
"
5"
11 1 / 2 "
*Note: When used in combination with
another Electrolux ICON ® built-in product, a
minimum clearance of 3 1 / 8 " required from
bottom of Built-In Microwave cutout to top
edge of companion product’s faceplate,
leaving a 2" visible gap between both
product faceplates