Euro-Pro STEAM BLASTER EP95B - Manual (Page 3)

IMPORTANT SAFETY INSTRUCTIONS
USAGE SUGGESTIONS FOR SHARK STEAM BLASTER
When using your Shark Steam Blaster, basic safety precautions should always
be observed, including the following:
Important User Information
Please note that this steam cleaner has a “flow through injection” type boiler
and is not a pressurized system. It will take approximately 45-90 seconds for
the steam injector to heat up and the “steam ready light” to go off. Once the
steam ready light has gone off, push the steam switch on the handgrip to the
“On” position (I) in order to start the steam flow. Steam power will steadily
increase during the first four (4) minutes of use, after which time steam output
will stabilize. Some steam will condense around the floor brush when in use
and will cause hard surfaces to become wet during the cleaning process, this
is normal.
To reduce the risk of fire, electric shock, or
injury:
• Do not leave the Shark Steam Blaster
plugged in when unattended. Unplug the
electrical cord when not in use and before
servicing or refilling water tank.
• Do not allow to be used as a toy. Close
attention is necessary when used by or near
children, pets or plants.
• Use only as described in this manual. Use
only manufacturer’s recommended
accessories.
• Do not pull cord, use cord as a handle, close
a door on cord, or pull cord around sharp
edges or corners. Keep cord away from
heated surfaces.
• Do not use extension cords or outlets with
inadequate current carrying capacity.
• Turn off all controls as applicable before
unplugging from electrical outlet.
• Do not unplug by pulling on cord. To unplug,
grasp the plug, not the cord.
• Do not handle plug or steam cleaner with wet
hands or operate without shoes.
• Do not put any objects into openings. Do not
use with any opening blocked.
• Store your appliance indoors in a cool, dry
area.
• Keep your work area well lit.
• When in use, never turn the appliance over
or on its side. Never direct steam towards
people, animals or plants.
• Do not immerse the steam cleaner into water
or other liquids. Always unplug the power
cord from the electrical socket when filling the
steam cleaner.
• Do NOT add cleaning solutions, scented
perfumes, oils or any other chemicals to
the water used in this appliance as this
may damage the unit or make it unsafe for
use. Use tap water or distilled/purified
water if the tap water in your area is very hard.
1. Read all instructions before using your
Shark Steam Blaster.
2. Use the system only for its intended use.
3. To protect against a risk of electric shock,
do not immerse any part of the system in
water or other liquids.
4. Never yank cord to disconnect from
outlet; instead, grasp plug and pull to
disconnect.
5. Do not allow cord to touch hot surfaces.
Let the system cool completely before
putting away. Use “Cord Storage Hooks” for
power cord.
6. Always disconnect system from electrical
outlet when filling or emptying water tank
and when not in use.
7. Do not operate the system with a damaged
cord or plug, or if the appliance or any other
part of the system has been dropped or
damaged. To avoid the risk of electric
shock, do not disassemble or attempt to
repair the Shark Steam Blaster. Return
the system to EURO-PRO Operating LLC
(see warranty) for examination and repair.
Incorrect re-assembly or repair can cause a
risk of electrical shock or injury to persons
when the Shark Steam Blaster is used.
8. Close supervision is necessary for any
appliance being used by or near children.
Do not leave the system unattended while
connected.
9. Burns can occur from touching hot metal
parts, hot water or steam. Do not turn
upside down as there may be hot water in
the unit. Never direct steam at any person.
The steam is very hot and can cause burns.
10. Do not operate in the presence of
explosive and/or flammable fumes.
11. This appliance is intended only for
household use. Follow all user instructions
in this manual.
12. Never use any chemicals or substance
other than tap water in the machine. Use of
chemicals may damage the machine. Use
of chemicals will automatically void your
warranty.
Note : We strongly recommend the
use of two (2) 100 % cotton towels
layered one on top of the other.
Wood, Vinyl and Marble Floors
Use the floor brush with a 100% cotton
terry cloth attached, ( see page 7 for
details). Move the brush slowly in back
and forth motions. When the towel is
soiled, you can turn the towel over or
replace it with a clean towel. If you are
working on a very dirty area, we
recommend that you move the brush
over the area slowly, several times. If it
is a wood floor, do NOT leave the unit
stationary for any length of time to avoid
heat or moisture build-up in the wood.
By cleaning with the towel over the
brush, you will not affect the shine on the
floor.
To Clean Waxed Floors: Install a clean
towel(s) on the floor brush, work quickly.
The towel will absorb the dirt but not
remove the wax.
Vinyl Floors: Do not allow heat to buildup
in any kind of vinyl, since it can soften it
enough to affect its texture. Work quickly
on vinyl. Use two (2) towels on floor brush.
Tile Floors: For tile and marble floors only,
if there is an area of the floor which is
excessively dirty, you may remove the
towels and agitate the area with the brush
bristles directly. Do not let the area dry.
Wipe immediately with a clean cloth. Re-
clean with brush and towels in place.
Note: Do not use steam cleaner on
hardwood or vinyl floor without towels
installed on the floor brush.
Tips On How To Use Your
System
Water
• Use tap water for all your cleaning
needs, however, if you live in an area
with hard water, use
demineralized/distilled water.
Important: Do NOT add cleaning
solutions, scented perfumes, oils or any
other chemicals to the water used in
this appliance. Use tap water or
distilled/purified water if the tap
water in your area is very hard.
Temperature
• The vapor temperature at the tip of
the nozzle is between 220°F and 240°F.
• The temperature of the vapor falls to
100 °F at a distance of 10 inches from
the nozzle.
CAUTION : A towel wrapped around the
brush can become hot enough to burn.
Make sure that you let the towel cool off
before touching it or changing it.
• For best results use 100% cotton white
terry cloth towels.
• Use correct size (8” x 17”) of towel to
allow you to wrap the towel over the
ends of the brush and clip it under the
spring loaded towel clips.
• The purpose of using towels is to
absorb the moisture and dirt being
removed. Always use dry towels. A
wet towel will smear the dirt.
• Wash towels with strong detergent
and bleach.
Using Towels
• Using scented fabric softener while
washing the towels will cause the
scent to be released into the air when
using the towels with your steam
system.
SAVE THESE INSTRUCTIONS
For Household Use Only
8
Rev. 04/02C 1