Elkay CUSL-31 - Manual (Page 2)

All dimensions are in inches. To convert to millimeters, multiply inches by 25.4.
Illustration A ELKAY POINTS OF SUPERIORITY
1. Elkay “Lusterton” Custom Cabinet Sink and Countertops are fabricated of
#18 gauge nickel bearing (18-8, Type 304) stainless steel bonded to, and
reinforced with, #14 gauge steel plate and 3/4"x3/4"x1/8" angle iron.
2. Intersections where sink bowls meet drainboards are rounded to
sanitary radii.
3. Drainboard, sink bowls, raised rims and backsplash are welded,
ground and polished smooth to a one-piece seamless appearance.
4. All corners in sink bowls (horizontal and vertical) are rounded to
1 3/4-inch radii.
5. Drainboards have large, fan-shaped areas pitched to drain. To incorporate
pitch, drainboard must be minimum 15" long.
6. Entire underside of sink top and bowl is fully undercoated to dampen sound
and prevent condensation.
7. Superior surface finish and satin luster achieved through special hand
polishing operations by master craftsmen.
HOW TO PRICE
For Basic Counter Tops up to 25" wide
1. Add all wall dimensions to determine total linear inches of counter. From
Schedule for Countertops on page 3 locate total inches column one. Under
proper backsplash height column, read total price of basic counter.
2. When sink bowl is desired, add to price of basic counters, the price of sink
model chosen, as shown on pages 4 and 5 (custom sizes are available).
3. Add the price of all special features applicable, as shown on pages 6 and 7.
HOW TO ORDER
1. When ordering Elkay custom made stainless steel sink and countertops,
accuracy of dimensions is of the utmost importance.
2. Furnish a sketch of sink or counter arrangement marked with proper
dimensions, and special features. Remember, you cannot give too
much information.
3. Always include the following information:
a) Show dimension from end of counter to center line of single
compartment sink models…or
b) Show dimension from end of counter to center line of partitions of two or
more compartment sink models.
c) Specify model number of faucet and other trim desired, if not included
with the sink model chosen.
d) Indicate manufacturer’s name and complete model number of range unit
to be installed if applicable.
e) Indicate and locate all cutouts or special conditions you require.
(See pages 6 & 7.)
HOW TO MEASURE
1. Measure, in inches, along wall or walls where top is to be installed.
2. Establish overall counter width, front to back, (standard is 25"), including
backsplash thickness.
3. Determine height of backsplash (measured from top of raised rim.)*
(Standard is 4") Determine thickness of backsplash, (Standard is 1 1/2").
4. Determine sink bowl size and its location. (See pages 4 and 5.)
5. List special features such as range cutout, return ends, rounded corners,
etc. (See pages 6 and 7.)
* Explanatory Note:
Elkay Custom Sink Tops and Countertops are provided with our standard
5/32" raised rim. Flat rim is available at no additional charge. For rims other
than 5/32" or flat, please refer to Custom Feature #17 on page 7.
Wall Dimensions (4" Backsplash)
96"+ 126"+ 60"= 282":
Base 156" . . . . . . . . . . . . . . . .$ 3,041.00
Additional 126" @ $18.00 . . . . . . . . . . . . . . .2,394.00
(a) Field Joint w/4" back . . . . . . . . . . . . . . . . . .903.00
(b) “U" Weld w/4" back . . . . . . . . . . . . . . . . . . .722.00
(c) LR3722 Double Bowl . . . . . . . . . . . . . . . .1,621.00
(d) 12" Radius Calculations
Base 3" . . . . . . . . . . . . . . . . . . . .135.00
Additional 9" @ $26.00 . . . . . . . . . . . .252.00
(e) Range Cutout . . . . . . . . . . . . . . . . . . . . . . .304.00
(f) Partial Column Cut . . . . . . . . . . . . . . . . . . .311.00
(g) Full Column Cut . . . . . . . . . . . . . . . . . . . . .549.00
TOTAL LIST PRICE . . . . . . . . . . . . . . . . . . .$10,232.00
Limitation profile of sink when
wall faucets are used.
* 1 1/4" top thickness can be furnished when specified at no additional cost.
Limitation profile of sink when
deck faucets are used.
This is an example of pricing a
custom made unit. The sink is
Model LR3722, double
compartment, top has 4" high
backsplash and top has a flat rim.
List Price CUSL-31
Effective: December 4, 2006
(Supersedes CUSL-30)
Illustration B
Underside view of construction detail
Illustration C
2
HEIGHT OF BACK
FROM TOP OF
RAISED RIM
HEIGHT OF BACK
FROM TOP OF
RAISED RIM BOWL INSIDE
2" MIN.
2" MIN.
3 3/4"
MIN
3/4" OR
MORE
(1 1/2" STD.)
*1 1/2"
1 1/2" MIN.
*1 1/2"
BACKSPLASH
USUALLY 1 1/2"
THICK TO ALLOW
FOR SUPPLY LINES
14 GA. STEEL PLATE
REINFORCING
18 GA. STAINLESS STEEL TOP
WOOD STRIP
UNDERSIDE IS FULLY UNDERCOATED TO
DAMPEN SOUND AND PREVENT CONDENSATION.
STAINLESS STEEL TOP
WOOD STRIP
3/4" X 3/4" X 1/8"
ANGLE IRON
BOWL
EXCEEDS 1/8"
THICKNESS
126"
63"
2 1/8"
8"
12"
54"
96"
25"
25"
60"
8"
4"
WELD
(b)
FIELD JOINT
(a)
12"
12" RADIUS
(d)
PARTIAL
COLUMN CUT
(f)
FULL
COLUMN CUT
(g)
(c) (c)
RANGE
CUTOUT
(e)
DROP-IN
C Cu usstto om m M Maad dee SSiin nkk P Prro od du uccttss