Operating instructions – Euro-Pro WATER FILTRATION VACUUM CLEANER CW230H User Manual

Page 5

OPERATING INSTRUCTIONS

1. Add 3 cups, (24 oz) of water to the

tank.

2. Insert plug into electrical outlet.

3. To connect the flexible hose into

the air intake duct, align the arrow

on the hose with the arrow on the

unit. Push in and turn 90°

clockwise to lock the hose in

place. (Fig. 1)

4. Attach the flexible hose to the

cyclonic tube. (Fig. 1)

5. Push extension tube into the

cyclonic air intake opening and

attach desired accessory to the

other end. (Fig. 1)

NOTE:

Always remove the power plug

from the wall outlet before assembling or

removing accessories and/or filling or

emptying the water tank.

WARNING:

Water level

MUST NEVER

exceed the "Max" level indicated on the

water tank. Empty tank when water level

reaches "MAX" indicator. If water is seen

to be coming from the exhaust -

immediately turn the unit off and unplug

from electrical outlet. Empty water tank

and clean. Refill water tank with 3 cups

(24 oz.) of clean water then plug unit

back in and continue working.

IMPORTANT: DO NOT operate this

vacuum when water level is below the

water tube opening.

Fig. 1

Using Your Water Filtration
Vacuum For Dry Vacuuming

6. Turn the "On/Off" Switch to the "On"

position.

7. The flexible hose is equipped with a

manual suction control to adjust the

amount of suction required. For strong

suction ensure that suction button is

closed. To decrease amount of

suction slide the button to open until

desired strength is obtained. (Fig. 3)

Fig. 3

To Use the Dry Vac Feature

Without the Cyclonic Attachment:

8. Attach the wider end of one of the

extension tubes to the flexible hose

handle.

9. Attach the other extension tube to

the first one and ensure a tight

connection.

10. Attach the desired accessory to the

narrow end of the extension tube.

11. When finished using the unit,

unplug from electrical outlet and

empty the water from the unit.

Accessories for Use With the Dry

Vac Feature:

•

Air Driven Turbo Brush

•

Convertible Brush

•

Crevice Tool

•

Floor Brush

•

Cyclonic Attachment

Air intake

duct

Cyclonic

attachment

Extension

tube

Accessory

Manual

Suction

Control

Water Tube

7. If you still see that the pre-cleaner has

not been completely removed, repeat

steps 3 and 4 again.

8. If the stain has not been removed,

repeat steps 1 to 6 again.

NOTE: Pre-cleaner spot removers

sometimes do not remove tough stains.

Please use a professional carpet cleaning

service if such is the case.

Cleaning / Replacing Foam Inlet

Filter

1. Unplug unit from electrical wall outlet.

2. Lift the locking tabs on either side of

the water tank.

3. Lift the handle to remove the

removable cover. (Fig. 11) Empty the

water tank into a toilet or an outside

drain.

4. The foam inlet filter should be cleaned

regularly depending on

amount of usage.

Carefully remove the

foam inlet filter.

A severely soiled or

clogged filter should be thoroughly

washed with fresh tepid water. A mild

detergent may be used if required.

5. Let the foam inlet filter

air dry completely

before replacing in vacuum.

Do not use a washing

machine to rinse the

filter. Do not use a hair dryer to dry

it. Air dry only. Never operate the

vacuum without the foam inlet filter

in place.

6. The water tube may become clogged

with debris. Pull away from removable

cover and rinse under lukewarm water

and replace. (Fig. 12)

Cover

Removable

Cover

Canister
Locking

Tabs

Fig.11

Foam Inlet

Filter

Pre-motor

Filter

Fig. 7

Fig. 9

5. Dust cup may be rinsed

under lukewarm tap

water. Ensure that

dust cup is dry before

using. (Fig. 9)

Cleaning The Cyclonic Attachment

1. Do not allow dirt to go above the

“MAX” level.

2. Remove the cyclonic attachment from

flexible hose and any extension

tubes.

3. Hold cyclonic dust cup firmly and turn

the cover counter clockwise to unlock.

(Fig.7)

4. Firmly pull apart and empty dust cup.

(Fig. 8)

Fig. 8

Dust Cup

Lock

WARNING:

To reduce risk of electric

shock - unplug before cleaning or

emptying water tank.

WARNING:

Water level

MUST NEVER

exceed the

"Max" level indicated on the

water tank. Empty the tank

when the water level reaches

"MAX" indicator. If water is

seen to be coming from

the exhaust - immediately

turn the unit off and unplug from electrical

outlet. Empty the water tank and clean.

(Fig. 10) Refill water tank with clean

water to min. 3 cup level, then plug unit

back in and continue working.

Fig. 10

Emptying & Cleaning Water Tank

Water Tube

Fig. 12

Fig. 2