Parkside PDBS 6.2 A1 - Manual (Page 44)

44 GB/MT
General safety rules
Protect hoses from kinks, constrictions, solvents
and sharp edges. Keep hoses away from heat,
oil and rotating parts.
Make sure that the hose clamps are always
tightly fastened. If the hose clamps are not tightly
fastened or are damaged, the air could escape
uncontrollably.
Replace damaged hoses immediately. A damaged
supply line may result in the air hose flapping
about and may result in injuries.
If the power cable of the appliance is damaged,
it has to be replaced by the manufacturer or its
service department or a similarly qualified per-
son in order to avoid hazards.
Do not use the device when tired or under the
influence of drugs, alcohol or medications. One
moment of carelessness when using the device
may result in serious injuries.
Do not directly inhale the exhaust air. Keep eyes
away from exhaust air. Exhaust air from the air
tool may contain water, oil, metal particles or
contaminants from inside the compressor. This
may damage your health.
CAREFUL WHEN PUT-
TING THE TOOL DOWN! Always put down
the device so it does not come into contact with
the trigger. This could potentially result in acci-
dental activation of the device, which again
could result in hazards.
Only use suitable accessories. These may be pur-
chased from the manufacturer. Using non-OEM
accessories may result in hazards.
Only use filtered and regulated compressed air.
Dust, caustic vapours and/or moisture may
damage the motor of the compressed air tool.
The hose must be designed for pres-
sures of at least 8.6 bar or 125 PSI,
but at least 150 % of the maximum
pressure generated in the system.
The tool and supply line must be
equipped with a hose coupling to
completely release pressure when
disconnecting the coupling hose.
DANGER! Avoid contact with live lines. This
device is not insulated against electric shock.
RISK OF INJURY! High
working pressures can give rise to recoil forces
that under certain conditions can result in danger
from continuous loading.
If you are inexperienced in the use of this type
of device, you should seek training to learn how
to handle it safely.
DANGER OF STAB
WOUNDS! Do not treat an injection as a sim-
ple cut. A high pressure jet may inject toxins
into the body and cause serious injuries. If the
spray is injected into the skin, seek medical
help immediately.
Do not modify this device in any way without
the manufacturer‘s approval.
Only use the device with the specified pressure
(max. 6.2 bar).
Disconnect the compressed air unit from the air
supply after each use and when not in use.
Do not use the compressed air device if it leaks
or is in need of repair.
Never connect the compressed air device to an
air hose with pressure exceeding 6.2 bar.
Keep your working area clean and well lit. Un-
tidy or poorly lit working areas can result in ac-
cidents. Doing so will allow you better control
of the device, particularly under unforeseen cir-
cumstances.
Only have the device re-
paired by qualified specialist personnel using
OEM spare parts. This will maintain the safety
of the device.
Keep children and other persons away from the
device during use. Distractions can cause you
to lose control of the device.
Wear suitable clothing. Do not wear loose cloth-
ing or jewellery. Keep your hair, clothing and
gloves clear of moving parts. Loose clothing,
jewellery or long hair can become trapped in
moving parts.
Put down trigger and device in the event of un-
expected compressor failure.
If possible, use a condensate trap or drain the
hoses and pipes of condensate (water) regularly
before and during the use compressed air units.
ATTENTION! An undersized com-
pressed air system may minimise the
efficiency of your device.
For multiple hazards, read and understand the
safety instructions before installing, operating,
General safety rules
43096_par_Druckluft-Blechschere PDBS 6.2A1_content_ES_IT_PT.indd 44 28.05.14 16:59