Parkside PKS 1700 B2 - Manual (Page 67)

GB/MT
- 67 -
r
back of the equipment (Fig. 6).
6.3 Precision adjustment of the stop for
crosscut 90° (Fig. 7-8)
•
No stop angle included.
•
Fasten the turntable (16) in 0° position.
•
Undo the locking screw (23) and move the
machine head (5) all the way to the right
using the handle (1).
•
Place the 90° angular stop (z) between the
blade (7) and the turntable (16).
•
Slacken the counternut (d). Adjust the ad-
justment screw (90°) (29) until the angle
between the blade (7) and the turntable (16)
equals 90°.
•
Retighten the counternut (d) to secure this set-
ting.
•
Check the position of the pointer (21) on the
scale (20). If necessary, release the pointer
(21) with a crosstip screwdriver, move to the
0° position of the scale (20) and retighten.
6.4 Precision adjustment of the stop for
miter cut 45° (Fig. 1, 7, 10-11)
•
No stop angle included.
•
Fasten the turntable (16) in 0° position.
•
Undo the locking screw (23) and move the
machine head (5) all the way to the left using
the handle, until it coincides at 45°.
•
Place the 45° stop angle (y) between the bla-
de (7) and the turntable (16).
•
Adjust the adjustment screw (30) so that the
angle between the blade (7) and the turntab-
le (16) equals exactly 45°.
7. Operation
7.1 Cross cut 90° and turntable 0°
(Fig. 1-3, 12)
Important! The integral resetting springs will
automatically lift the machine head. Do not simply
let go of the handle (1) after cutting, but allow the
machine head (5) to rise slowly, applying slight
counter pressure as it does so.
For cutting widths up to approx. 100 mm it is
possible to fi x the saw’s drag function with the
locking screw for drag guide (24) in rear position.
If the cutting width exceeds 100 mm you must
ensure that the locking screw for drag guide (24)
is slackened and that the machine head (5) can
be moved.
•
Move the machine head (5) to its upper posi-
tion.
•
Use the handle (1) to push back the machine
head (5) and fix it in this position if required
(dependent on the cutting width).
•
Place the piece of wood to be cut at the stop
rail (19) and on the turntable (16).
•
Lock the material with the clamping device
(8) on the fixed saw table (17) to prevent the
material from moving during the cutting ope-
ration.
•
Push down the release lever (3) to release the
machine head (5).
•
Press the ON/OFF switch (2) to start the mo-
tor.
•
With the drag guide (26) fixed in place: use
the handle (1) to move the machine head (5)
steadily and with light pressure downwards
until the saw blade (7) has completely cut
through the workpiece.
•
With the drag guide (26) not fixed in place:
pull the machine head (5) all the way to the
front. Lower the handle (1) to the very bottom
by applying steady and light downward
pressure. Now push the machine head (5)
slowly and steadily to the very back until the
saw blade (7) has completely cut through the
workpiece.
•
When the cutting operation is completed,
move the machine head (5) back to its upper
(home) position and release the ON/OFF
Anl_4300689.indb 67 Anl_4300689.indb 67 10.10.12 18:58 10.10.12 18:58