Earthquake Sound MiniMe P10 - Manual (Page 5)

(1) Line Level RCA Inputs terminals will accept up to 16-gauge quality speaker
Connect with RCA type patch cords to the line level wire. The Inputs should be connected to the left and
output of your receiver or pre-amp. If your pre- right speaker terminals of your amplifier or receiver.
amplifier or receiver has a single sub/LFE output, The Outputs should run from the subwoofer to the left
connect it to the subwoofer's left input jack. There is and right satellite speakers. Remember: Always
no need to use the subwoofers right input jack. If you connect red-to-red and black-to-black, when making
want to run your main/satellite speakers full range, connections between an amplifier/receiver to the
use a "Y" adapter at the pre-amplifier outputs. In this subwoofer. If you inadvertently reverse one of the
way, you can send the pre-amplifier's output signal to connections (i.e., red-to-black), you will notice a lack
your main amplifier and to the subwoofer at the same of bass from your subwoofer.
time.
(3) Voltage Selection Switch
(2) High Level Inputs / Outputs
Under normal conditions, the preferred connection is
through the Line Level inputs. If this is difficult or not
possible in your system, then you can use the
Speaker Level inputs. Also, if you experience
excessive noise or hum with the Line Level input,
often a simple change to the Speaker Level input will
result in a lower background noise level.
(4) Manual ON/OFF Switch
Connect the Speaker Level inputs to the speaker-level In the “ON” position, the subwoofer will remain “on”
outputs of your amplifier or receiver using speaker constantly or can turn “on” and “off” automatically
wire. The binding posts can accept bare wire when the “AUTO/ON” circuit is engaged. In the “OFF”
connections only. position, the subwoofer will remain off until the switch
is manually turned back to the “ON” position.
High Level: Connecting the Subwoofer using the high
level speaker connections: On the rear of your MiniMe
(5) Line Fuse
Subwoofer are two pairs of red and black binding The subwoofer is supplied with a conservative, slow-
posts. One set is marked “Input” and one set is blow type fuse to protect the electronics.
marked “Output”, with each pair designated as left or
right. Each post is color-coded black/red. These
The voltage switch is positioned according to area
voltage requirements. It has been pre-set
prior to shipping from the factory.
CAUTION
Do not try to alter the voltage setting, as doing so will
result in a blown fuse. A wrong setting
may result in damaged electronics.
Control Panel Overview
Overview Continued On Next Page»
(5) Line Fuse
(9) 0-180° Phase Shift
(11) 50Hz - 160Hz
Frequency Adjustment
(12) Volume Control
(10) Sub Operation Switch
(8) Power Status LED
(1)
Inputs and Outputs Line Level RCA
(7) Auto ON/OFF
(2) Speaker
Inputs and Outputs Level
(4) Manual ON/OFF Switch (3) Voltage Selection Switch
(6) 110-120V AC Power Connection
Earthquake • MiniMe User Manual 5
Earthquake Sound, 2727 McCone Avenue, Hayward, CA 94545 USA
www.earthquakesound.com
VOLUME
FREQUENCY
MODE
PHASE
AUTO
MIN
50Hz
MAX
RIGHT
POWER
LEFT
160Hz
SUB
0
OFF
LFE
180
ON
110-120VAC~60Hz
220-240VAX~50Hz
FUSE: 115V, T6.4AL/250V
FUSE: 230V, T3.2AL/250V
ON
110-120V
220-240V
OFF
TO REDUCE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL
WARNING
WARNING: SHOCK HAZARD-DO NOT OPEN
AVIS: RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR
RISK OF ELECTRIC SHOCK DO NOT OPEN
CAUTION
P O W E R
DIGITAL
600 WATTS
POWERED
SUBWOOFER
FUSE