Euro-Pro SELECT EP922H - Manual (Page 7)

NOTE: Fit floor brush with the angle
adapter on to the extension
tube.
Step 2: If the angle adapter is not
attached to the floor brush, hold
the brush with its bristles up in
your left hand. With the angle
adapter pointing downward,
insert it into the hole in the back
of the brush, then turn the floor
brush 180°.
Step 3: Insert the electrical power cord
into the wall outlet. Heating
time is approximately 8-10
minutes with cold water. Filling
the steam generator with hot
water will shorten the heat up
time.
Fig. 3
Cleaning the Floor Brush
To clean the floor brush after you have
finished using:
1. Lift the front clip on the floor
brush (Fig. 4) and remove the brush.
2. Rinse the bristle brush and the
diffuser housing under warm water.
3. Replace bristle brush onto the diffuser
housing.
Fig. 4
Fig. 2
Step 1: Connect one of the extension
tubes to the hand grip on the
flexible steam hose. To
attach the extension tubes
one onto the other or onto the
hand grip, press the locking
button ensuring that it fits into the
hole. (Fig. 2, Fig. 3) To
disconnect, repeat the operation
by pressing the locking button
and pulling the two sections
apart.
OPERATING INSTRUCTIONS
Attaching the Shoulder Strap
Using the detachable shoulder strap
allows for greater freedom of movement
when both hands are needed for
various cleaning tasks.
To attach the shoulder strap to the
steam cleaner, simply snap the
shoulder strap hooks onto the
connecting rings on the unit body.
See Fig. 17, 18 & 19.
IMPORTANT: When using the
portable steam cleaner with the
shoulder strap, avoid rocking or
tilting the unit excessively as this
may cause water to enter the
hose and be discharged along
with the steam.
Fig. 17
Fig. 19
Fig. 18
Assembling the Caddy
The casters for the caddy for the
portable steam cleaner are packed
and shipped unassembled. To
assemble the casters to the caddy,
simply insert the caster stem into one
of the four (4) holes in the base and
push downward with the palm of your
hand. (Fig. 20.) Repeat for the next
three (3) casters.
Fig. 20
Attaching the Portable Steam
Cleaner to the Caddy
1. After you have inserted the castors
to the base of the caddy, turn the
caddy right side up on a flat, level
surface. Place it with the rear
locking latch to your right.
2. Hold the portable steam cleaner
with the power cord also to your
right.
3. Insert the left side of the
portable steam cleaner (#1 in the
illustration below) down into
the caddy making sure that it
clips into the front locking tab.
4. Then press down on the right
side of the portable steam
cleaner (#2 in the illustration
below) so that the rear locking
latch locks in place. (Fig. 21)
Fig. 21
Rear
Locking
Latch
Front
Locking
Tab
OPERATING INSTRUCTIONS
Using Your Steam Cleaner
with Floor Brush Attaching a Towel to the Floor
Brush
Important: Please note that bristles may
break through thin towels. To cut and make
your own towels, we recommend that you
use one (1) towel 8” x 17” folded in half or
two (2) towels 4” x 17” laid one on top of
the other be used. This will ensure that the
brush bristles do not break through and
that the towels will be sufficiently absorbent
and retain as much dirt as possible.
Very Important : When installing the
towels to the floor brush, ensure that the
towels do not cover the front and the back
of the brush. (See Fig. 9)
100% white terry cloth towel can be fitted
on this brush, so as to absorb the dirt and
protect delicate surfaces.
Fig. 5
1. Prepare white terry cloth towel:
size 8” x 17” folded in half or place one
on top of another to have two layers.
(Fig. 5)
Fig. 6
3. Fold the towel as shown in Fig. 6.
2. Place the brush on top of the towel.
6
9