Aquatic AV AQ-DVD-4 - Manual (Page 13)

1) Traffic Alert (TA)
TA SEEK is the default setting. User now has 5 seconds to select TA SEEK or TA ALARM by
pressing the VOLUME+/- buttons
TA SEEK
When a newly tuned station does not receive TP information for several seconds, the radio
retunes to next station which has not the same station (PI) as the last station, but has the
TP information. When TP information gets lost at the current station for retune time which is
set by RETUNE SHORT (30 sec.) or RETUNE LONG (90 sec.), the radio start to retune to
next same PI station. When same PI station does not catch in 1 cyclic search, the radio re-
tunes to next station with TP information.
TA ALARM
When this mode is selected any automatic retune mode is not activated. Only double beep
sound (ALARM) is output.
When a newly tuned station does not have TP information for several seconds, beeps come
out. When TP information gets lost at the current station for retune time, the beep sound is
out-putted. When newly tuned station has not RDS signal PI SEEK is suppressed some-
what.
2) Program Identification
PI MUTE is the default setting. User now has 5 seconds to select : PI MUTE to PI SOUND
by pressing the VOLUME+/- buttons.
While AF switching is implemented in C201 station, AF can switch to 100MHz, which is non
genuine AF (where, different PI with same AF) in short “DIP” with same AF) in short “DIP”.
If a car cruises that critical area back and forth, an oscillation phenomenon can be occurred,
because the different PI code can be received from 100 MHz with “XXX” PI.
The car radio has special procedure to reduce even this kind of unavoidable situation how-
ever there is a limit to be escaped from this serious case perfectly. In that serious case, 2
mode is selectable as follows:
13
www.aquaticav.com
SETTINGS OPERATION - RDS MENU
A
Q
-D
V
D
-4
RDS - TRAFFIC ALERT (TA)
RDS - PROGRAMME IDENTIFICATION
iPOD & iPHONE OPERATION
IPOD OPERATION
● iPod 1G: Not Supported
● iPod 2G: Not Supported
● iPod 3G: Firmware Version2.2
● iPod Mini: All versions
● iPod 4G: All versions
● iPod Photo: All versions
● iPod Nano: All versions
● iPod 5G(Video): All versions
● iPhone: All versions
● iPhone 3G: All versions
● iPhone 3GS: All versions
● iPhone 4: All versions
The AQ-DVD-4 allows direct control of the IPOD from the front panel control buttons and will
display IPOD song information on the unit’s LCD display.
PLAYING & CONTROLLING iPOD/ iPHONE
SWITCH TO IPOD/IPHONE MODE
When the unit is powered ON and iPod/iPhone is connected to the 30 pin connector, press
the MODE button to change to iPod/iPhone mode and the unit will display “IPOD” then
“IPOD READING” shortly after. The music files contained in the iPod/iPhone will then auto-
matically playback.
TURNING IPOD/IPHONE POWER ON/OFF
The iPod/iPhone power turns on automatically as soon as it is connected to the 30 Pin
connector and so long as the power is ON.
The iPod/iPhone power can be turned OFF by removing the iPod from the 30 Pin Connector
or if the AQ-DVD-4 is turned OFF. Under this condition the iPod/iPhone will initially go into
pause mode and then into sleep mode approximately two minutes later.
While the iPod/iPhone is connected the power can not be turned on/off from the
iPod/iPhone itself.
iPOD/ iPHONE COMPATIBILITY
When connected to the AQ-DVD-4 the iPod/iPhone will display the message shown
below:
28
www.aquaticav.com
AQDVD4 Manual_V1.4_FINALV1:Layout 1 10/11/2011 20:13 Page 25