Loops – Verilink 310 (CG) (CG) Configuration/Installation Guide User Manual
Page 2
T
R
A
N
S
P
O
R
T
®
7
6
5
4
3
2
1
9
7
6
5
4
3
2
8
S1
S2
V.35
1
93-130
VAC
1 - 5 DSOs Assigned: These five positions select the bit rate and the number of DSOs assigned to the
channel (refer to the table below).
6
Rate Multiplier: Sets the multiplier for the input timing (refer to the table below). The unit oper-
ates at any data rate that is a multiple of 56 or 64 kbps.
7
Channel Assignment: The Contiguous mode assigns the channels as a block beginning at DS0
channel 1. If ‘Alternate’ is selected, channel assignments are made with an idle channel following
each data channel.
8
Control Lines: ‘On’ permanently sets the CTS, DSR, and CD leads to ON. With ‘Follow’, the
DSR lead follows T1 sync, the CTS lead follows RTS, and the CD lead follows the density status
of the incoming T1 signal (
≥
175 zeros = CD OFF). The TM line goes high when the unit is in a
local or remote test mode.
9
Data Invert: Determines whether the data bits are inverted.
NOTE: The ‘A’ position is the factory default for
all switch settings. If a particular user configuration
requires that a switch be placed in the ‘B’ direction,
then mark this sheet for future reference.
Circuit Pin #
Signal Name
DCE
101
A
Frame Ground
Ground
102
B
Signal Ground
Ground
103
P/S
Transmit Data
In
104
R /T
Receive Data
Out
105
C
Request To Send
In
106
D
Clear To Send
Out
107
E
Data Set Ready
Out
109
F
Data Carrier Detect
Out
113
U /W
External Transmit Clock
In
114
Y/AA
Transmit Clock
Out
115
V/X
Receive Clock
Out
142
K
Test Mode
Out
V.35 Interface
DSO S1 - 1 S1 - 2 S1 - 3 S1 - 4 S1 - 5 S1 - 6 (A) S1 -6 (B)
1
B B B B B 56
kb 64
kb
2
B A B B B 112
128
3
A A B B B 168
192
4
B B A B B 224
256
5
A B A B B 280
320
6
B A A B B 336
384
7
A A A B B 392
448
8
B B B A B 448
512
9
A B B A B 504
576
10
B A B A B 560
640
11
A A B A B 616
704
12
B B A A B 672
768
13
A B A A B 728
832
14
B A A A B 784
896
15
A A A A B 840
960
16
B B B B A 896
1024
17
A B B B A 952
1088
18
B A B B A 1008
1152
19
A A B B A 1064
1216
20
B B A B A 1120
1280
21
A B A B A 1176
1344
22
B A A B A 1232
1408
23
A A A B A 1288
1472
24
A A A A A 1344
1536
DTE
NET
Local Loopback
DTE
NET
Remote Channel Loop (V.54)
DTE
NET
* Signal regeneration only
*
CSU Line Loop (Inband or LLB)
Loops
1
Data In (R1)
2
Data In (T1)
3 /6
Not Used
4
Data Out (R)
5
Data Out (T)
7 /8
Chassis Gnd
Network Pinout
1 - 2 Timing Source: This position selects the source of unit clocking (refer to the Switch S2 table).
3
Not used.
4
Network Framing: This position selects the network framing to either ESF or D4.
5
Network Coding: This position selects the network line code format to either AMI or B8ZS.
6 - 7 Network LBO: This position selects the network LBO (line build out) signal level of the data
transmitted towards the T1 facility (refer to the Switch S2 table).
Switch S1 Description
Switch S2 Description
6
5
4
3
1
7
9
8
2
56 k
bps
C
o
ntiguou
s
C
o
ntrol
D
at
a In
v
ert
64
kbps
Al
ter
n
ate
Contr
o
l
Dat
a I
n
v
er
t
F
o
llo
w
On
No
Ye
s
Switch S1
DSOs Assigned
(see table at bottom)
8
1
NET
A
B
A
B
127 Jetplex Circle
Madison, Alabama 35758
Sales and Marketing
800-926-0085
205-772-3770
RMA/ Returns
800- 926-0085, ext. 2282
Technical Support
800-285-2755
205-772-3770
Not
ES
F
AM
I
No
t
D4
B8Z
S
5
4
3
2
1
6
7
B
A
A
A
B
A
Network clock (looped)
Internal clock (master)
CPE clock (external)
Timing
Source
Network
LBO
B
B
B
A
A
A
B
A
0
-22.5
-7.5
-15
Switch S2
A
B
Us
ed
Us
ed
B B Not Valid