Teac AI-1000 - Manual (Page 9)

Troubleshooting Specifications
Amplifier Section
Power output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85 W + 85 W (8 Ω)
120 W + 120 W (4 Ω)
Frequency response . . . . . . . . . . . . . . . . . . . . . . . . 10 Hz - 30 kHz (-0.5 dB)
Signal noise ratio. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 dB (A-weighted)
Total harmonic distortion . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.01 % or less
Input sensitivity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .280 mV/47 kΩ
General
Power supply
Europe model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AC 230 V, 50 Hz
USA/Canada model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AC 120 V, 60 Hz
Power consumption (nominal)
Europe model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .240 W
USA/Canada model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .160 W
Dimensions (W x H x D) . . . . . . . . . . . . . . . . . . . . . . . . 435 x 116 x 403 mm
Weight. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10.0 kg
Operating temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +5˚C - +35˚C
Operating humidity. . . . . . . . . . . . . . . . . . 5 % - 85 % (no condensation)
Storage temperature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –10˚C - +55˚C
Accessories
Power cord x 1
Remote control x 1
AAA battery x 2
Warranty card x 1
Owner's manual x 1
Design and specifications are subject to change without notice. o
Weight and dimensions are approximate. o
Illustrations may differ slightly from production models. o
9
ENGLISH
If you experience any problems with the unit, please take a moment
to look through this chart before asking for repairs. If you still have
a problem, contact your dealer or TEAC customer service/technical
support (stated on the back cover).
No power
e Check the connection to the AC outlet. Check and make sure
the AC source is not a switched outlet and that, if it is, the switch
is turned on. Make sure there is power to the AC outlet by
plugging another item such as a lamp or fan into the outlet.
Remote control doesn't work.
e Press the POWER switch of the main unit to turn it on.
e If the batteries are dead, change the batteries.
e Within the specified range of 10 m, point the remote control
directly at the unit's front panel.
e Clear any obstacle between the remote control unit and the
main unit.
No sound
e Check the connection to the amplifier.
e Check the operation of the amplifier.
e Muting is activated. Press the MUTE button. Select the correct
source.
e Output protection has been activated. Turn off the unit,
check for possible causes (e.g. short-circuited speaker cables,
connected speakers with wrong impedance) and solve the
problem. Wait 5 minutes before turning on the power again.