dbx Pro 1215 - Manual (Page 2)

DUAL CHANNEL 15 BAND EQUALIZER
1215
The graphic equalizer shall be a dual 15-band type with frequency centers
on standard ISO two-thirds octave frequencies ranging from 25Hz to
16kHz. The boost/cut ranges shall be switchable via recessed front panel
switches to either +/-6dB or +/-15dB and the selected range shall be
indicated on the front panel by either of two LEDs per channel. Low-noise
equalization sliders having a 45mm travel shall be utilized having center
detents at 0dB. The equalizer shall have front panel 41-detent rotary input
gain controls having a +/-12dB range. Bypassing the equalizer sections of
the signal path shall be accomplished via front-panel switches having
corresponding LEDs to indicate when each channel is bypassed. A 40Hz
low-cut Bessel filter per channel with 18dB/octave slope shall be insertable
in the signal path via front panel recessed switches with an LED to indicate
when the filter is active. Output levels shall be monitored on four-LED
peak-reading bar graphs calibrated to read -10, 0, +10, and +18dBu.
Electronically balanced/unbalanced inputs shall include 1/4" TRS, female
XLR, and screw terminal barrier strip, while servo-balanced/unbalanced
outputs shall include 1/4" TRS, male XLR, and screw terminal barrier strip
shared with the input. A circuit/chassis ground lift jumper per channel shall
be strapped across circuit ground and chassis ground screw terminals and
shall be removable by the user. Inputs shall be electronically
balanced/unbalanced and RF filtered having a nominal input impedance
not less than 40kΩ balanced and 20kΩ unbalanced, and shall accept
maximum signal levels of not less than +21dBu. Outputs shall be servo-
balanced/unbalanced and RF filtered having a nominal output impedance
of not more than 200Ω balanced and 100Ω unbalanced, and shall be
capable of driving not less than +21dBu into 2kΩ or greater and not less
than +20dBm (into 600Ω) continuously.
Frequency response shall be better than 10Hz to 50kHz, +0.5/-3dB. Signal-
to-noise ratio shall be greater than 90dB, referenced to +4dBu. THD+Noise
shall be less than 0.005% with a 1kHz signal at +4dBu, while interchannel
crosstalk shall be lower than -80dB from 20Hz to 20kHz.
The internal power supply shall be constructed using a thermally-fused transformer mounted in a low hum orientation and shall
be magnetically isolated from equalizer circuitry by means of a mu-metal shield. The power cord shall be detachable from an
international standard IEC 320 power inlet receptacle. Unit shall be constructed to meet or exceed all applicable international
safety and regulatory agencies. Domestic unit shall be powered from 100VAC 50/60Hz, 120VAC 60Hz, while international unit
shall be powered from 230VAC 50/60Hz. Unit shall consume no more than 24W. Housing shall be of all steel/aluminum
construction and shall be rack-mountable in an IEC standard 19" rack and shall occupy a 2U (3.5") rack space. The unit shall be
a dbx 1215 Equalizer.
dbx engineers are constantly working to improve the quality of our products. Specifications are, therefore subject to change
without notice.
®
FOR MORE INFORMATION CONTACT:
dbx Professional Products
8760 S. Sandy Pkwy.
Sandy, Utah 84070
Phone (801) 568-7660
Fax (801) 568-7662
Int’l Fax (801) 568-7583
[email protected]
http://www.dbxpro.com
A Harman International Company
RANGE
CHANNEL ONE
OUTPUT
LEVEL (dBu)
LOW
CUT
EQ
BYPASS
INPUT
GAIN
dB -12
0
+12
+/-6
+/-15 CLIP
0
-6
+6
25 40 63 100 160 250 400 16k 10k 6.3k 4k 630 1k 1.6k 2.5k
+18 +10 0 -10
1215
Graphic Equalizer 0
-15
+15
RANGE
CHANNEL TWO
OUTPUT
LEVEL (dBu)
LOW
CUT
EQ
BYPASS
INPUT
GAIN
dB -12
0
+12
+/-6
+/-15 CLIP
0
-6
+6
25 40 63 100 160 250 400 16k 10k 6.3k 4k 630 1k 1.6k 2.5k
+18 +10 0 -10
0
-15
+15
OUTPUT INPUT
PHONE:
TIP
RING
SLEEVE XLR:
PIN 1
PIN 2
PIN 3
CONNECTOR POLARITY
INPUT OUTPUT
OUTPUT INPUT
INPUT OUTPUT
PROFESSIONAL PRODUCTS
A HARMAN INTERNATIONAL
COMPANY
MODEL 1215
GRAPHIC EQUALIZER
W A R N I N G : T O R E D U C E T H E R I S K O F F I R E O R E L E C T R I C
S H O C K D O N O T E X P O S E T H I S E Q U I P M E N T T O R A I N O R M O I S T U R E
R I S K O F E L E C T R I C S H O C K
D O N O T O P E N
AT T E N T I O N : R I S Q U E D E C H O C E L E C T R I Q U E - N E P A S O U V R I R
C A U T I O N : T O R E D U C E
T H E R I S K O F F I R E R E P L A C E
O N LY W I T H S A M E T Y P E F U S E .
AT T E N T I O N : U T I L I S E R
U N F U S I B L E D E R E C H A N G E D E
M E M E T Y P E .
24 WATTS
POWER
100V 50/60Hz
120V 60Hz
MANUFACTURED UNDER ONE OR MORE OF THE FOLLOWING
U.S. PATENTS: 4,234,804 4,316,107 4,329,598 4,331,931 4,377,792
4,403,199 4,409,500 4,425,551 4,434,380 4,454,433 4,471,324
4,473,793 OTHER PATENTS PENDING
OUTPUT
- +
INPUT
- +
OUTPUT
- +
INPUT
- +
CHANNEL 1
CHANNEL 2
586
Dual Vacuum Tube Preamp
TYPE IV™ Conversion System
704
Inputs
Connectors: 1/4" TRS, female XLR (pin 2
hot), and barrier terminal strip
Type: Electronically
balanced/unbalanced, RF
filtered
Impedance: Balanced 40kΩ, unbalanced
20kΩ
Max Input Level: >+21dBu balanced or
unbalanced
CMRR: >40dB, typically >55dB at
1kHz
Outputs
Connectors: 1/4" TRS, male XLR (pin 2
hot), and barrier terminal strip
Type: Impedance-
balanced/unbalanced, RF
filtered
Impedance: Balanced 200Ω, unbalanced
100Ω
Max Output Level: >+21dBu
balanced/unbalanced into
2kΩ or greater
>+18dBm
balanced/unbalanced (into
600Ω)
System Performance
Bandwidth: 20Hz to 20kHz, +0.5/-1dB
Frequency Response: <10Hz to >50kHz, +0.5/-3dB
+/-15dB range +/-6dB range
Dynamic Range: 109db 115db
Signal-to-Noise: 90db 97db
THD+Noise: <0.005%
Interchannel Crosstalk: <-80dB, 20Hz to 20kHz
Function Switches
EQ Bypass: Bypasses the graphic
equalizer section in the signal
path
Low Cut (recessed): Activates the 40Hz
18dB/octave Bessel high-
pass filter
Range (recessed): Selects either +/- 6dB or +/-
15dB slider boost/cut range
Indicators
Output Level: 4-LED bar graph (Green,
Green, Yellow, Red) at -10, 0,
+10, and +18dBu
EQ Bypass: 1 LED: red
Clip: 1 LED: red
Low Cut: 1 LED: red
+/-6dB: 1 LED: yellow
+/-15dB: 1 LED: red
Power Supply
Operating Voltage: 100VAC 50/60Hz, 120VAC
60Hz, 230VAC 50/60Hz
Power Consumption: 1215 24W; 1231 24W
Mains Connection: IEC receptacle
Physical
Dimensions: 1215: 3.5" H X 19" W X 7.9"
D (8.9cm x 48.3cm x 20.1cm)
1231: 5.25" H X 19" W X
7.9" D (13.4cm x 48.3cm x
20.1cm)
Weight: 1215: 8.5 lbs.
1231: 10.6 lbs.
Shipping Weight: 1215: 9.5 lbs.
1231: 11.6 lbs.
Note: Specifications subject to change.