Ravenheat WH 100 - Manual (Page 3)

3
SERVICING SHOULD BE CARRIED OUT BY A
QUALIFIED GAS SAFE REGISTERED INSTALLER
The White Boiler Company
Chartists Way , Morley , Leeds
LS27 9ET
PROGRAMMABLE TIMECLOCK
INSTRUCTIONS FOR USE
If your boiler comes complete with optional digital
programmer.
7. TO PROGRAMME TIMECLOCK
The timeclock is supplied with a cover to prevent
accidental loss of programme, or children tampering
with pre-set programmes.
To access programming buttons remove clear cover.
Press reset key with a pencil before setting or
reprogramming times.
7.1.1 TO SET TIME AND DAY OF THE WEEK:
7.1.1.1 SET DAY OF WEEK:
- Press clock button and hold in.
Press day button to desired day.
- Release both buttons.
The day of the week will be set.
7.1.1.2 SET HOUR:
- Press clock button and hold in.
Press hour button to desired time.
- Release both buttons.
The hour will be set.
7.1.1.3 SET MINUTE:
- Press clock button and hold in.
Press minute button to desired time.
- Release both buttons.
The minute will be set.
NOTE: When setting time holding in the hour/minute
button will rapidly advance the display.
7.1.2 TO SET PROGRAMMES:
7.1.2.1 Press timer button and release to enter into
programme mode.
7.1.2.2 Programme “1 ON” will show in lower left hand
corner.
7.1.2.3 Press
DAY key to select the programme pe-
riod. There are 10 day settings for your choice.
(1) Mo to Su (2) Mo (3) Tu (4) We (5) Th (6) Fr (7) Sa
(8) Su (9) Mo+Tu+We+Th+Fr (10) Sa+Su.
You now have a choice of setting up to 6 programmes.
7.1.2.4 Press hour button to set the required hour.
7.1.2.5 Press minute button to set minute.
7.1.2.6 After setting the programme press the
TIMER
key again “1 OFF” will appear.
N. B.: When the clock is either “programmed” on, or is on constant, the red indicator will illuminate.
Repeat procedure 5.1.2.3 through to 5.1.2.5 to set
programme “1 OFF”required settings.
For each programme the days OFF setting must be
input the same as the ON setting (see 5.1.2.3).
7.1.2.7 After setting programme 1 ON/OFF TIME
repeat step 2.1 to 2.7 to set programmes 2 through to
6 if required.
7.1.2.8 Your timer gives you up to 6 different ON and
6 different OFF settings over the programme periods
as defi ned in 5.1.2.3.
NOTE: You have a choice of 6 ON - 6 OFF
programmes max.
7.1.2.8.1 REVIEW YOUR PROGRAMMES:
- Press the TIMER key to advance display to each
subsequent ON or OFF setting.
- Check days and times displayed.
- To make a change, follow instructions under
“TO SET PROGRAMMES”.
NOTE: on completion of programming operations
press the clock button to show current time/day and
replace the clear tamper proof cover.
7.1.2.8.2 MANUAL KEY
- Press MANUAL key to select ON / AUTO / OFF
mode.
- ON mode is to turn on the timer, OFF mode is to turn
off the timer.
- AUTO mode is to set the timer to programme mode.
It will turn on or turn off according to the programmes
you set.
- From ON to AUTO mode it will turn on until next OFF
programme.
- From OFF to AUTO mode it will turn off until next ON
programme.
7.1.2.8.3 LED INDICATOR
The red LED light is on when the timer is operating in
heating mode.
7.1.3 TO RESET TIMER:
Press reset button to reset the timer unit.
NOTE:
Once the reset button is pressed, the stored
time and programme will be cleared to initial state.