Proel NEOS152AXS User Manual
Neos152axs, User manual, Digital self-powered loudspeaker
USER MANUAL
NEOS152AXS
digital self-powered loudspeaker
KEY FEATURES
• Premium transducers
• C-AUDIO CLASS D power amplifi ers with SWITCH MODE power supply
• 96KHz, 40bit fl oa ng point C-AUDIO CORE DSP
• Network func onality thru PRONET control so ware
• Access to EQ, DYNAMICS and DELAY and real me parameter control
• Plywood cabinets with die-cast handles, dual-angle pole holder and mul ple fl ying points
INTRODUCTION
NEOS AXS series represents the highest expression of PROEL GROUP Research & Development applied in loudspeaker systems. A natural evolu on
of the NEOS Series, it incorporates the latest technologies developed by PROEL in advanced sound reinforcement systems able to provide premium
sound, maximum performance and up-to-date features.
NEOS AXS is a complete range of self-powered loudspeaker systems combining cu ng-edge transducers with C-AUDIO CLASS D amplifi ers and
digital processors, thus ensuring the best integra on between acous cs and electronics for an op mal performance.
The NEOS AXS are designed for the use both as high-performance mobile systems for live applica ons and as versa le and remotely controllable
systems for advanced fi xed installa ons.
All the models are powered by C-AUDIO DA power modules, a new genera on of CLASS D power amplifi ers with SWITCH MODE power supply, able
to provide an excep onal sound defi ni on together with very high dynamics and low distor on in an ultra-compact package.
The on board control electronics are based on the 96KHz, 40bit fl oa ng point C-AUDIO CORE DSP pla orm, able to op mize further the system
performances through the use of sophis cated EQ, crossover and dynamics algorithms. The CORE processing provides also network func onality
through the PRONET control so ware based on CANBUS communica on protocol (USB2CAN converter needed).
The PRONET control so ware provides access to the major processing features, including full PARAMETRIC and DYNAMIC EQ, advanced
COMPRESSOR/LIMITERS and DELAY, together with the real me control of parameters such as temperature, supply voltage and protec ons.
Se ng created by the user can be saved in user presets that can be recalled through the control so ware or from the unit’s interface.
TECHNICAL SPECIFICATION
AcousƟ cal
Mechanical
System type
Full range 2-way, vented
Construc on
15 and 18 mm birch plywood
Low frequency driver
15’’ neodymium woofer - 4” VC
Finish
An -scratch black paint
High frequency driver
2’’ compression driver - tanium diaphragm - 3” VC
Flying hardware
6 x fl y tracks side and rear
Frequency response
40 Hz - 20 kHz
Trapezoidal taper
10°
Horn type
Asymmetrical rotatable horn
Monitor taper
42°
Coverage
90°>60° H x 50° V
Pole holder
1 bo om dual angle (0° / 7.5°)
Max SPL
132 dB
Dimensions (W x H x D)
450 x 770 x 490 mm
Electrical
Weight
36 kg (79.4 lb)
Input Impedance
20 kohm balanced, 10 kohm unbalanced
Frequency Response Diagram
Input Sensi vity
+4 dBu / 1.25 V
black = FLAT gray = MONITOR
Signal Processing
CORE processing 24 bit / 96 kHz
Amplifi er type
C- AUDIO Class D with SMPS
Output power
1000 + 1000 W
Connectors
IN - LINK: XLR M - XLR F
NETWORK IN - OUT: ETHERCON® (NE8FAV)
MAIN LINK: PowerCon® (NAC3MPB)
MAIN: PowerCon® (NAC3MPA)
Controls
LEVEL, PRESET (FLAT / HPF / MONITOR/ USER)
TERMINATE, GND LIFT
Cooling
Variable speed DC fan
Power Supply
230 VAC or 120 VAC 50/60 Hz
Max consump on
1650 VA
1/8 power out consump on
550 VA
10k
5k
2k
1k
500
200
100
50
40
20k
Hz
120.0
dBSPL
110.0
100.0
90.0
80.0
70.0