Proel NEOS215AXS - Manual

USER MANUAL
NEOS215AXS
digital self-powered subwoofer
KEY FEATURES
• Premium transducers
• C-AUDIO CLASS D power amplifi ers with SWITCH MODE power supply
• 96KHz, 40bit fl oa ng point C-AUDIO CORE DSP
• Network func onality thru PRONET control so ware
• Access to EQ, DYNAMICS and DELAY and real me parameter control
• Plywood cabinets with die-cast handles, dual-angle pole holder and mul ple fl ying points
INTRODUCTION
NEOS AXS series represents the highest expression of PROEL GROUP Research & Development applied in loudspeaker systems. A natural evolu on
of the NEOS Series, it incorporates the latest technologies developed by PROEL in advanced sound reinforcement systems able to provide premium
sound, maximum performance and up-to-date features.
NEOS AXS is a complete range of self-powered loudspeaker systems combining cu ng-edge transducers with C-AUDIO CLASS D amplifi ers and
digital processors, thus ensuring the best integra on between acous cs and electronics for an op mal performance.
The NEOS AXS are designed for the use both as high-performance mobile systems for live applica ons and as versa le and remotely controllable
systems for advanced fi xed installa ons.
All the models are powered by C-AUDIO DA power modules, a new genera on of CLASS D power amplifi ers with SWITCH MODE power supply, able
to provide an excep onal sound defi ni on together with very high dynamics and low distor on in an ultra-compact package.
The on board control electronics are based on the 96KHz, 40bit fl oa ng point C-AUDIO CORE DSP pla orm, able to op mize further the system
performances through the use of sophis cated EQ, crossover and dynamics algorithms. The CORE processing provides also network func onality
through the PRONET control so ware based on CANBUS communica on protocol (USB2CAN converter needed).
The PRONET control so ware provides access to the major processing features, including full PARAMETRIC and DYNAMIC EQ, advanced
COMPRESSOR/LIMITERS and DELAY, together with the real me control of parameters such as temperature, supply voltage and protec ons.
Se ng created by the user can be saved in user presets that can be recalled through the control so ware or from the unit’s interface.
TECHNICAL SPECIFICATION
AcousƟ cal Mechanical
System type Sub-woofer, vented Construc on 15 and 18 mm birch plywood
Low frequency driver 2 x 15’’ woofer - 3” VC Finish An -scratch black paint
Frequency response from 40 Hz Flying hardware 2 x M10 - top
HP fi lter preset 120 Hz - 80 Hz Pole holder 1 top - 1 side
Coverage omnidirec onal Dimensions (W x H x D) 590 x 760 x 850 cm
Max SPL 136 dB Weight 62.5 kg (138 lbs)
Electrical
Input Impedance 20 kohm balanced, 10 kohm unbalanced Frequency Response Diagram
Input Sensi vity +4 dBu / 1.25 V
black = 120 Hz gray = 80 Hz
Signal Processing CORE processing 24 bit / 96 kHz
Amplifi er type C- AUDIO Class D with SMPS
Output power 1500 W
Connectors
IN - LINK: XLR M - XLR F
NETWORK IN - OUT: ETHERCON® (NE8FAV)
MAIN LINK: PowerCon® (NAC3MPB)
MAIN: PowerCon® (NAC3MPA)
Controls
LEVEL, PRESET (80 Hz / 120 Hz / 180° / USER)
TERMINATE, GND LIFT
Cooling Variable speed DC fan
Power Supply 230 VAC or 120 VAC 50/60 Hz
Max consump on 2200 VA
1/8 power out consump on 730 VA
1k 500 200 100 50 20 20 1k Hz
120.0
dBSPL
110.0
100.0
90.0
80.0
70.0