Monster SoundStage Wireless Home Music System S1 Mini Bluetooth Speaker - Manual (Page 5)

8 9
Input / Output Panel Overview
WPS
Enable WiFi Protected Setup.
Mode
Change WiFi Mode.
Press and hold for 10 seconds and release to reset
wireless network settings.
Micro USB
Micro USB port used for updating Monster® Soundstage™
firmware.
Audio In
3.5mm stereo audio input.
Digital Input
Optical (Toslink) digital input.
USB DC Power Output
Standard USB out port for charging portable devices
(2.1 A).
DC-IN: AC 100V–240V Adaptor Connector
Input from power supply.
Factory Reset
Recessed reset button back to factory default. Insert
paperclip and hold for ten seconds to reset.
A
B
C
D
E
F
G
H
The Monster ® SoundStage
™
System
Monster® Soundstage™ is a whole house wireless
music system. You can connect up to ten (10) Monster®
Soundstage™ speakers plus headphones via Bluetooth
wireless, all controlled by the Monster® Soundstage™ App.
Check www.monsterproducts.com/soundstage for more
detailed instructions, upcoming product releases and news.
Compatibility
Wireless
Devices with Bluetooth® 2.0 wireless technology or above
(See General Specifications for profiles), such as Bluetooth
wireless technology equipped computers, and most
Bluetooth wireless technology equipped smartphones
and MP3 players.
Music content on networked devices connected to the
same WiFi network as the Monster® SoundStage™ system
will be accessible from within the Monster® SoundStage™
app menu.
Wired
Devices with a standard 3.5 mm headphone output port
via 3.5 mm minijack cable (not included).
Devices with a Digital Toslink output can connect directly to
the digital input via Toslink cable (not included).
Safety
Do not leave the product exposed to a heat source or
extreme temperatures.
The product should not be exposed to dripping or splashing
and objects filled with liquids, such as vases, should not be
placed on the apparatus.
FCC ID: RJE-173221
This device complies with Part 15 of FCC Rules. Operation is
subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) This device must
accept any interference received, including interference that
may cause undesired operation. Changes or modification not
expressly approved by the party responsible for Compliance
could void the user’s authority to operate the equipment.
Connecting of peripherals requires the use of grounded
shielded signal cables. The socket-outlet shall be installed
near the equipment and shall be easily accessible.
NOTE: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause
harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more
of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment
and receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV
technician for help.
Caution
Changes or modifications not expressly approved by the
party responsible for compliance could void the user’s
(or your) authority to operate the equipment.
Avoid storage in extreme heat or cold. Avoid exposure
to liquids, temperature extremes and high humidity. The
product’s working temperature range is 0–45°C (32–113°F).
Industry Canada
This device complies with Industry Canada license-exempt
RSS standard(s). Operation is subject to the following two
conditions: (1) this device may not cause interference, and
(2) this device must accept any interference, including
interference that may cause undesired operation of
the device.
Dieline Blade Speaker Small
Units: mm Scale: 1:1
Date: 05/23/2014
Version 6
D E F G A B C
H
ENGLISH
ENGLISH
855866_LIT_MAN_SoundStage_S1_V4td.indd 8-9 9/22/14 12:03 PM