beautypg.com

Operation procedures – Marantz PM601 0OSE User Manual

Page 2

background image

4

English

E

E

E

E

E

GND (GROUND) TERMINAL

Connect the grounding wire from the turntable to this terminal.

F

F

F

F

F

TAPE

CD-R/MD IN/OUT JACKS

Connect the play (output) jacks and record (input) jacks of tape decks
to these jacks.
Up to three tape decks can be connected.

NOTE:

When a surround processor or graphic equalizer is used, it must be
connected to the

TAPE

jacks.

G

G

G

G

G

SPEAKER SYSTEMS

Connect your speaker system to these terminals.

H

H

H

H

H

REMOTE CONTROL (BUS) TERMINALS

Another item of audio equipment with a remote control (bus) terminal can
be connected to these terminals by using a special-purpose cable. The
bus OUT terminal is used to send signals to another item of equipment.
The bus IN terminal is used to receive signals from another item of
equipment.

I

I

I

I

I

POWER CORD

Connect to a household power outlet.

q

q

q

q

q

POWER SWITCH

Pressing once switches the power

ON

, and pressing again switches it

OFF

. The

POWER

indicator lights when the

POWER

switch is

ON

, and

go out when the

POWER

switch is

OFF

.

w

w

w

w

w

INPUT SELECTOR

Selects the program source to be recorded or played from the

PHONO

,

CD

,

TUNER

,

AUX

.

e

e

e

e

e

VOLUME CONTROL

Adjusts the volume level. Turn the knob clockwise to increase the
volume.
You can also operate the amplifier with a remote control unit.

r

r

r

r

r

BALANCE CONTROL

Turn the knob to correct an unbalanced program source such as stereo
broadcast or to vary the output level of the left or right channel.
Note that, if the

BALANCE

control is turned fully in one direction, the

sound will not be heard from the speaker on the other side.

t

t

t

t

t

TAPE

CD-R/MD SWITCHES

Press one of these switches to monitor the playback sound of a tape
deck connected to the rear panel of this unit.
When the

CD-R/MD

switch is pressed, this unit automatically enters the

tape dubbing mode, the

COPY CD-R

fi

TAPE

indicator lights, and the

playback signal of CD-R or MD can be copied onto tape deck.
Set both of the switches to OFF when the CD-R or MD, tape decks are
not to be played.
For details, refer to "TAPE DECK OPERATION".

y

y

y

y

y

SOURCE DIRECT SWITCH

When this switch is pressed, the audio signal is supplied directly to the
volume control circuitry (the signal is directed through the minimum
required path to improve the reproduction of high-quality sources).

NOTE:

When this switch is ON, the settings of the tape monitor switches,
and balance control are ignored.
While this switch is depressed, recording, playback, or dubbing of
tapes cannot be carried out even when a tape monitor switch is
pressed.

u

u

u

u

u

IR SENSOR

The remote sensor receives the infrared commands from the remote
control unit. When an infrared signal is received from the remote control
unit. The remote control unit must always be pointed directly at the
remote sensor.

i

i

i

i

i

MUTING INDICATOR

Light up when the

MUTING

button in the remote control unit is pressed.

NOTE:

Be sure to check the VOLUME control setting before pressing this
switch to cancel muting, If the muting is canceled while the volume
setting is high, the speakers could be damaged.

o

o

o

o

o

PHONES JACK

Insert the standard phone plug of the headphones into this jack.

OPERATION PROCEDURES

TO PLAY AN ANALOG RECORD

1.

Set the

INPUT SELECTOR

switch to

PHONO

.

2.

Play a record on the turntable.

3.

Adjust the volume with the

VOLUME

control.

NOTES:

• Set the

VOLUME

control to the minimum position before placing the

stylus on the record or before replacing the cartridge.

• Do not apply shock or vibration to the turntable during play, as this

may cause the stylus to jump and the analog record to be damaged.

• If the turntable is installed too close to the speakers, the volume may

not be able to be increased to a high level due to howling.

• Do not switch the power OFF while the stylus is on the record surface.

TO LISTEN TO FM/AM BROADCASTS

1.

Set the

INPUT SELECTOR

switch to

TUNER

.

2.

Tune in the desired station on the tuner.

3.

Adjust the volume with the

VOLUME

control.

TO PLAY A COMPACT DISC

1.

Set the

INPUT SELECTOR

switch to

CD

.

2.

Play a CD on the CD player.

3.

Adjust the volume with the

VOLUME

control.

TO PLAY A COMPONENT CONNECTED TO AUX JACKS

The component connected to the

AUX

jacks on the rear panel can be

played as follows.

1.

Set the

INPUT SELECTOR

switch to

AUX

.

2.

Play the component connected to the selected input.

3.

Adjust the volume with the

VOLUME

control.

TAPE

CD-R/MD

SOURCE DIRECT

INTEGRATED AMPLIFIER PM6010OSE

TAPE

CD-R/MD

MUTE

MIN

MAX

L

R

COPY

CD-R>TAPE

CD

PHONO

TUNER

AUX

INPUT SELECTOR

VOLUME

BALANCE

POWER ON/OFF

PHONES

ON

OFF

ON

OFF

ON

OFF

2 Operate each equipment to start play.

1

3