Marantz SR5023 - Manual (Page 17)

13 13
BASIC
CONNECTIONS
BASIC
OPERA
TION
ADV
ANCED
CONNECTION
ADV
ANCED
OPERA
TION
TROUBLESHOOTING
OTHERS
NAMES AND FUNCTIONS
ADV
ANCED
OPERA
TION
ENGLISH
TUNER OPERATION (PRESET MEMORY)
With this unit you can preset up to 50 FM/AM stations
in any order.
For each station, you can memorize the frequency
and reception mode if desired.
AUTO PRESET MEMORY
This function automatically scans the FM and AM
band and enters all stations with proper signal
strength into the memory.
DISP AUTO TUNED ST
SLEEP DIRECT
2. 4. 5. 2. 1. 3.
1. To select FM, press the BAND button on the
front panel.
2. While pressing the MEMORY button, press the
TUNING/PRESET 3 button.
“AUTO PRESET” will appear on the display,
and scanning starts from the lowest frequency.
3. Each time the tuner fi nds a station, scanning
will pause and the station will be played for fi ve
seconds.
During this time, the following operations are
possible.
The band can be changed by the BAND button.
4. If no button is pressed during this period, the
current station is memorized in location Preset
01.
If you wish to skip the current station, press the
TUNING/PRESET 3 button during this period,
this station is skipped and auto presetting
continues.
5. Operation stops automatically when all 50
preset memory positions are fi lled or when auto
scanning attains the highest end of all bands.
If you desire to stop the auto preset memory at
anytime, press the CLEAR button.
Note:
It is possible that existing preset memory positions
will be overwritten.
MANUAL PRESET MEMORY
D ST
2. 4. 3.
2.
3.
(Using the unit)
1. Tune into the radio station you desire (Refer to
the “MANUAL TUNING” or “AUTO TUNING”
section).
2. Press the MEMORY button on the front panel.
“– –“ (preset number) starts blinking on the
display.
3. Select the preset number by pressing the
TUNING/PRESET 3 or 4 buttons, while this
indicator is still blinking (approx. 5 seconds)
4. Press the MEMORY button again to enter. The
display stops blinking.
The station is now stored in the specified
preset memory location.
(Using the remote controller)
1. Tune into the radio station you desire (Refer to
the “MANUAL TUNING” or “AUTO TUNING”
section).
2. Press the MEMO button on the remote
controller. “– –“ (preset number) starts blinking
on the display.
3. Enter the desired preset number by pressing
the numeric buttons.
Note:
When entering a single digit number (2 for example),
either input “02” or just input “2” and wait for a few
seconds.
RECALLING A PRESET STATION
DISP AUTO TUNED ST
SLEEP DIRECT
1. 1.
1.
(Using the unit)
1. Select the desired preset station by pressing
the F/P button and TUNING/PRESET 3 or 4
buttons on the front panel
(Using the remote controller)
1. Press the 1 or 2 buttons to select the desired
preset station, or input your desired preset
channel with the numeric buttons on the
remote controller.
PRESET SCAN
3.
1.
3.
3.
(Using the remote controller)
1. Press the P.SCAN button on the remote
controller.
“PRESET SCAN” appears on the display and
then the preset station with the lowest preset
number is recalled fi rst.
2. Preset stations are recalled in sequence (No.1
→ No.2 → etc.) for 5 seconds each.
No stored preset number will be skipped.
3. You can fast forward the preset stations by
pressing the 2 button continuously.
When the desired preset station is received,
cancel the preset scan operation by pressing
the CLEAR button or P.SCAN button on the
remote controller.
CLEARING STORED PRESET STATIONS
You can remove preset stations from the memory
using the following procedure.
3. 2.
3.
2.
1. Recall the preset number to be cleared with
the method described in “Recalling” a preset
station.
2. Press the MEMORY button on the front panel
or press the MEMO button on the remote
controller.
3. The stored preset number blinks in the display
for 5 seconds. While blinking, press the
CLEAR button on the front panel or the remote
controller.
4. “xx CLEAR” appears on the display to indicate
that the specified preset number has been
cleared.
Note:
To clear all stored preset stations, press and hold the
CLEAR and the F/P buttons on the front panel for
two seconds.