Marantz SR4001 - Manual (Page 43)

40
ENGLISH
CLEARING STORED PRESET STATIONS
You can remove preset stations from the memory
using the following procedure.
CAT
P.SCAN
CAT
T.MODE
1 2 3
4 5 6
7 8 9
0 +10
HT-EQ
MULTI/
MENU
SPKR A/B
INFO
CH/
INPUT
M-SPKR
MUTE
EX/ES VIRTUAL CS
VOLUME
dts
7.1CH IN
STEREO NIGHT M-CH ST
AUTO
A/D
LIP SYNC/
CL CL MEMO MEMO
2.
3.
DIGITAL VIDEO S-VIDEO AUX 1 INPUT T-MODE
MEMORY DISPLAY MUTE
VOLUME
DOWN
EXIT BAND
CLEAR
ENTER
2. 3.
1. Recall the preset number to be cleared with
the method described in “Recalling” a preset
station.
2. Press the MEMO button on the front panel or
press the MEMO button on the remote.
3. The stored preset number blinks in the display
for 5 seconds. While blinking, press the CLEAR
button on the front panel or the remote.
4. “ xx CLEAR ” appears on the display to indicate
that the specified preset number has been
cleared.
Note:
To clear all stored preset stations, press and hold the
CLEAR and the ENTER buttons for two seconds.
SORTING PRESET STATIONS
MULTI SPEAKER
DIGITAL R L VIDEO S-VIDEO AUX 1 INPUT AUDIO
SETUP SIMPLE MULTI PURE
T-MODE
SURROUND MEMORY DISPLAY ATT MUTE
STANDBY
PHONES POWER ON/STANDBY
INPUT SELECTOR VOLUME
UP DOWN
AV SURROUND RECEIVER SR5001
DIRECT
AUTO HT-EQ EXIT MENU
MODE
BAND
CLEAR
ENTER
If you have stations memorized, and there is a gap in
the sequential order:
I.e. the stations are stored as follows
1) 87.1 MHz
2) 93.1 MHz
3) 94.7 MHz
10) 105.9 MHz
(notice there is no stations programmed for pre sets
for 4-9), you can have pre set 10 become pre set 5:
To sort the numbers, press and hold the
MEMO and
the 4 cursor buttons.
“ PRESET SORT ” will appear on the display and
sorting will be done.
NAME INPUT OF THE PRESET STATION.
This function allows the name of each preset channel
to be entered using alphanumeric characters.
Before name inputting, you need to store preset
stations with the preset memory operation.
CAT
-
T.DISP F.DIRECT PTY
PRESET +
7 8 9
0 +10
CAT CAT
TUNING TUNING - - + +
HT-EQ
MULTI/
MENU
SPKR A/B
EXIT
INFO
T.TONE
/SET UP
M-SPKR
MUTE
DVD VCR DSS TV
VOLUME
BASS TREBLE
7.1CH IN
REC
AUDIO ANGLE SUB TITLE DISC+
CH-SEL V-OFF ATT.
A/D
CL
ENTER ENTER
MEMO MEMO
CH/ CH/
2. 5. 6.
5.
4.
MULTI SPEAKER
DIGITAL R L VIDEO S-VIDEO AUX 1 INPUT AUDIO
SETUP SIMPLE MULTI PURE
T-MODE
SURROUND MEMORY DISPLAY ATT MUTE
STANDBY
PHONES POWER ON/OFF
INPUT SELECTOR VOLUME
UP DOWN
AV SURROUND RECEIVER SR5001
DIRECT
AUTO HT-EQ EXIT MENU
MODE
BAND
CLEAR
ENTER
5. 2. 5. 6. 4.
1. Recall the preset number to be inputted name
with the method described in “Recalling” a
preset station.
2. Press the MEMO button on the front panel or
press the MEMO button on the remote for more
than 3 seconds.
3. The left most column of the station name
indicator fl ashes, indicating the character entry
ready status.
4. When you press the 3 or 4 cursor buttons on
the front panel or the 5 / 6 buttons on the
remote, alphabetic and numeric characters will
be displayed in the following order:
A → B → C ... Z → 1 → 2 → 3 ..... 0 → – → +
→ / → (Blank) → A
UP →
← DOWN
5. After selecting the fi rst character to be entered,
press the MEMO or ENTER buttons, press the
MEMO button on the remote.
The entry in this column is fi xed and the next
column starts to fl ash. Fill the next column the
same way.
To move back and forth between the characters,
press the 1 / 2 cursor buttons or press S or
T buttons on the remote.
Note:
Unused columns should be fi lled by entering blanks.
6. To save the name, press the MEMO button
on the front panel or remote for more than 2
seconds.
Ten keypad Press, press again, press again, etc.
1 A → B → C → 1 → A
2 D → E → F → 2 → D
3 G → H → I → 3 → G
4 J → K → L → 4 → J
5 M → N → O → 5 → M
6 P → Q → R → 6 → P
7 S → T → U → 7 → S
8 V → W → X → 8 → V
9 Y → Z → space → 9 → Y
0 – → + → / → 0