La Crosse Technology WS-7097 - Manual (Page 3)

• Serves the selection of the displays of current date with weekday, worldtime with location or alternating display of
both above modes every 5 seconds on LCD 1.
TIMEZONE Key
• Serves to enter the time zone change mode. The preset time zone on LCD 2 will start flashing. By use of the + key
the time zone can now be selected (±12hours). Alter the time zone to Hawaii (HAW, -10), Alaska (ALA, -9), Pacific
(PST, -8), Mountain (MST, -7), Central (CST, -6), Eastern (EST, -5; default time zone), Atlantic (AST, -4) and
Greenwich Mean Time (GMT, 0).To acknowledge the selected value and to exit this setting mode and return to
normal display mode, press the SET key or wait appr. 15 seconds for an automatic switch back.
LANGUAGE Key
• Serves to enter the selection mode for the one language by which the weekday is to be displayed on LCD 1.
Selection takes place by use of the “+” key from following languages:
GB English
D German
F French
I Italian
NL Dutch
DK Danish
E Spanish
J Japanese
To acknowledge the selected language and to exit this setting mode and return to normal display mode, press the
LANGUAGE key or wait appr. 15 seconds for an automatic switch back.
HYGRO Key
• Serves to select humidity and outdoor display. Pressing of the key will subsequently switch the display to the next
mode.
1.
Indoor relative humidity
2. Indoor relative humidity / Outdoor temperature
3. Outdoor temperature
+ Key
•
Serves in programming mode the change/selection of all changeable/selectable values and displays.
Manual programming
Note:
If the World Time Center has already successfully received the WWVB time signal and displays the correct time
and date, then the Manual programming can be omitted.
After completion of the above described procedures in “Basic Setup” the manual programming mode can be entered
by pressing the “SET” key for about 2 seconds.The following settings can now be programmed:
•
•
•
•
•
•
•
•
•
•
12/24 hour setting
Time setting
Weekday setting
Month setting
Date setting
Year setting
World Time location setting
World Time setting
ºC or ºF setting
LCD contrast setting
Note:
If in programming mode no key is pressed for appr. 15 seconds then the LCD will switch back to the normal display
mode.
12/24 Hours Setting
After entering the programming mode as described above the 12/24 hours display can be selected on LCD 2 in the
following way:
1. The
“12h” or “24h” will start flashing (Default setting 12h). Select the desired time display mode by use of the
“+”key.
Note:
In 12 hours mode the date will be displayed in the configuration “Weekday / Month / Day”, in 24 hours mode in
“Weekday / Date / Month”.
2. Press the “SET” key to enter the “Time Setting“.
Time Setting
1.
The hour digits will start flashing on LCD 2. Set the desired hours by pressing the “+” key followed by pressing the
“SET” key.
2. Now the minute digits will start flashing. Set the desired minutes by pressing the “+” key followed by pressing the
“SET” key to move to the “Weekday Setting”.
Note:
In 12 hours mode the time will be displayed with an additional “PM” for the time from 12:00 noon until 11:59.
Weekday Setting
1.
The weekday symbols will be displayed on LCD 1 in the preset language and flashing. Set the desired weekday by
use of the “+” key.
2. Press the “SET” key to enter the mode “Month Setting”.
Month Setting
1.
The month digits on LCD 1 will start flashing. Set the desired month by use of then “+” key.
2. Press the “SET” key to move to the mode “Date Setting”.
Date Setting
1.
The digits for the date will start flashing on LCD 1 (Default setting 1). Set the desired date by use of the “+” key.
Note:
The date can only be set in conjunction with the selected month. I.e., it is not possible to set the date 30 if the
month of February is selected.
2. Press the “SET” key to enter the mode “Setting of Year”.
Year Setting
1.
The year digits will start flashing on LCD 1 (Default setting 1998). Select the desired year by use of the “+” key.
Note:
The year can be selected sequentially from 1998 to 2020 and will then start over again. The year furthermore will
only be visible on the display of LCD 1 in programming mode.
3. Press the “SET” key to switch to the mode “Worldtime Location Setting”.
Worldtime Location Setting
1.
The dash representing the first character of the worldtime location (Default setting - - -) on LCD 1 will start flashing.
Select the desired character by use of the “+” key.
2. Press the “SET” key to move to the second character.
3. The second dash will start flashing. Select the desired character by use of the “+” key.
4. Press the “SET” key to switch to the third character.
4. The third dash will start flashing. Select the desired character by use of the “+” key.
Note:
For designation of the worldtime location the characters “A” through “Z” and “0” as well as “-” and “ ” (Space)
can be chosen.
6. Press the “SET” key to move to the mode “World Time Setting”.
World Time Setting