Kleenmaid RHSGSPOT User Manual

Page 15

Operation –
Model with electronic controls

A - Lighting, on/off.
B - Fan off (Stand by)
C - Timer for selected speed (visualises the speed selected

and flashing LED on the lower side of the display).
This knob permits the operation of the rangehood
for an established period:
20 minutes if the speed selected is 1
15 minutes if the speed selected is 2
10 minutes if the speed selected is 3
5 minutes if the intensive speed "P" is selected.

D - Display showing:

• Fan speed (1-3-P).
• Change grease filters (grease filter saturation indicator -

F)
After washing the anti-grease filter, depress knob "B" for
about 3 seconds. The letter F will disappear from the
display.

• Change activated carbon filters (carbon filter saturation

indicator - "C").
After replacing the charcoal filter, depress knob "B" for
about 3 seconds. The letter "C" will disappear from the
display.

• When the led in the lower right side is on, it indicates that

the rangehood is ready for operation (“standby” position),
the flashing LED indicates that the timer has been activated
for selected speed.

Warning!
The active carbon filter saturation function is not activated.
In order to activate the carbon filter saturation indicator,
press buttons "E" and "F" simultaneously for 3
seconds. Initially, only the letter "F" will be displayed,
then after the 3 seconds have passed, letter "C" will be
displayed as well, indicating that the carbon filter saturation
control system is active.
To switch off the system, re-press the same two buttons:
the letter "C" will appear on display and after 3 seconds
it will disappear and the device will be switched off.

E - Knob to decrease the speed: from intensive speed "P" to

speed level 1.

F - Knob to increase (standby) speed to intensive speed "P".

Attention! Intensive speed "P" has a duration of 5 minutes
after which the rangehood automatically sets the speed to
level 2 (suction power).

If the rangehood fails to operate correctly, briefly disconnect it
from the mains power supply for approx. 5 sec. by pulling out the
plug. Then plug it in again and try once more before contacting the
Technical Assistance Service.

Warning!
Always press the fan off button "A" before disconnecting the
rangehood from the mains supply.

Operation –
Model with electronic controls

1- Motor OFF button
2- ON button and motor speed selection button 1 - 2 - 3 - 1 - 2 -

. . . .

3- Speed 1 LED
4- Speed 2 LED and metal grease filter saturation LED (in this

latter case, the LED will flash - See instructions on grease filter
cleaning).
Once the grease filters have been cleaned, press button 1 for
about 3 seconds until you hear the acoustic signal (beep): the
LED 4 will now stop flashing.

5- Speed 3 LED and active carbon filter saturation LED in the

latter case, the LED will flash - See instructions on active
carbon filter replacement).
Once you have replaced the charcoal filter, press button 1 for
about 3 seconds until you hear the acoustic signal (beep). LED
5 will now stop flashing.
Warning!
The active carbon filter saturation LED is not activated.
In order to activate the active carbon filter saturation indicator,
press buttons 2 and 7 simultaneously for 3 seconds. Initially,
only LED 4 will flash, then after the 3 seconds have passed,
LED 5 will also start flashing, indicating that the active carbon
filter saturation control system is active.
To switch off the system, re-press the same two buttons: after
3 seconds LED 5 will stop flashing and the device will be
switched off.

6 - Intensive speed LED
7 - Intensive speed ON switch

This speed should be used when the concentration of cooking
fumes or odours is particularly strong (for example when frying,
cooking fish etc.) The fast speed will run for about 5
minutes and then return to the speed previously set automatically
(1, 2 or 3), or switch off if no speed was selected.
To turn off the fast speed, before the end of the 5 minutes, press
button 1 or button 2.

8 - OFF lamp button
9 - ON lamp button

2 3 4

5 6 7