Datexx RC224W - Manual (Page 2)

7 8
6 5
PROGRAMMING THE SNOOZE INTERVAL
* Press and hold SET1 button for two seconds to
activate an Alarm1 programming mode. Alarm1 hour
digit will flash.
* Adjust the desired hour using UP ( ) or DOWN ( )
buttons.
* Press SET1 button: the minute digits will flash.
* Adjust the desired minutes using UP ( ) or
DOWN ( ) buttons.
* Press SET1 button again:
the snooze interval minutes
will flash.
* Adjust the desired interval time using UP ( ) or
DOWN ( )buttons.
* Press SET1 button to confirm set snooze interval.
Use the same procedure to program the snooze interval
for Alarm2.
INDOOR TEMPERATURE
The indoor temperature shares the same display’s line
with the calendar and the day of the week.
NOTE: If the indoor temperature goes above or below
operating range stated in specifications, the display will
show dashes [ ].
SETTING THE ALARM
To set the Alarm1,
* Press MODE button once to display
ALARM TIME 1. If the alarm is off,
the default time “6:00” will be
displayed.
* Press and hold SET1 button for two
seconds. The hour digit will flash.
* Enter the hour using DOWN ( ) or
UP ( ).
* Press SET1 button again.
The minute digits will flash.
* Enter the minutes using DOWN ( )
or UP ( ).
* Press SET1 button again to
confirm:
an icon [ ] will appear on the
display next to the alarm time.
* Repeat the same procedure to set an
Alarm2, using SET2 button.
LIGHT/SNOOZE
When the alarm sounds, press the LIGHT/SNOOZE
button to temporarily stop the alarm. After the LIGHT/
SNOOZE is depressed, the alarm sound will resume in
five minutes.
If the alarm is not disabled after that, it will sound for
four more minutes and then will stop by itself.
DISABLING ALARM
Press SET1 or SET2 buttons on the unit to disable any of
the alarms.
When Alarm1 and Alarm2 are disabled, an applicable
icon [ ] or [ ]will disappear from the unit’s display.
TIME FORMAT
* Press UP ( ) button to toggle
between 12 and 24 hour time format
DAY OF THE WEEK LANGUAGE
* Press and hold DOWN ( ) button
for 3 seconds: the default language
abbreviation will flash (example – EN)
* Continue holding DOWN ( )
button until the desired day of the
week language abbreviation is
selected.
* Release the DOWN ( ) button to
confirm the setting.
ALARMS
There are two available alarms –Alarm 1 and Alarm 2.
If any of alarms is activated, it will sound at the set time
and the alarm icon will flash Mondays through Fridays.
PRECAUTIONS
This product is engineered to give you years of satisfactory
service if handled carefully. Here are a few precautions:
* Do not immerse the unit in water.
* Do not clean the unit with abrasive or corrosive
materials. They may scratch the plastic parts and
corrode the electronic circuits.
* Do not subject the product to excessive force, shock,
dust, temperature, or humidity, which may result in
malfunctions, shorter lifespan, damaged batteries, and
damaged parts.
* Do not tamper with the unit’s internal components.
Doing so will invalidate the warranty and may cause
damage. The unit contains no user-serviceable parts.
* Use only fresh batteries. Do not mix new and old batteries.
* Read the user's manual thoroughly before operating
the unit.
1
1 2
New
Moon
Waning
Crescent
Waning
Crescent
First
Quarter
Waxing
Gibbous
Full
Moon
Waning
Gibbous
Last
Quarter
PM
D M
1
2
D M
1
2
PM
D M
1
2
PM
D M
1
2
PM
D M
1
2
PM
D M
AM
PM
D M
AM
PM
D M
1 AM
MOON PHASE
Moon phase indicator is displayed in accordance with
the calendar.
PM
D M
1
2