Fire Magic Aurora Stand-Alone Quick Start Guide - Manual (Page 2)

4-Grill Setup
Parts Placement Checklist
Place the following items according to their position and orientation in
Fig. 4-1:
Flavor grids, cooking grids, backburner cover, warming rack, meat probe.
Leave pre-installed E-burners in place to maintain proper alignment.
Backburner Cover (if equipped)
Hook the backburner cover over the top of the backburner to protect the
backburner from grease, dust and dirt when it is not in use.
Warming Rack
The warming rack comes pre-installed. Remove zip ties before use.
Consult the owner’s manual to remove or replace.
Shelf/Sideburner (if equipped)
Align the four (4) holes in the shelf with the four (4) holes in the side of
the cart while aligning and engaging the burner venturi with the orifi ce
(Fig. 4-2). Insert the four (4) screw (provided) into the holes and tighten.
Make the igniter wire connection as shown in Fig. 4-2. Open sideburner
lid, set cap on burner, and set grid into shelf.
Screws
Air shutter
Orifi ce Igniter wire
Fig. 4-2
Venturi
Center main burner control knob
(A540s and larger only)
Fig. 5-2
Left
main burner
control knob
Right main burner
control knob
Backburner
control knob
(if equipped)
Digital
thermometer Meat probe
Sideburner
control knob
(if equipped)
Drip tray
Fig. 4-1
Cooking Grid
Flavor Grid
(not with IR)
Backburner
cover
Warming
rack
Cotter
Pin
Rotisserie
rod storage
ring
Sideburner
lid
Note: For infrared burner equipped
grills; see detailed instructions
included in your owners manual.
Meat probe
Drip tray
liners
Drip tray (with
lighting instructions)
6-Propane Safety
Gas Cylinders
IMPORTANT: READ AND FOLLOW ALL WARNINGS PROVIDED WITH THE PROPANE-GAS CYLINDER.
READ ALL SAFETY INSTRUCTIONS AND WARNINGS REGARDING THE USE OF PROPANE GAS FOUND IN
YOUR OWNERS MANUAL.
5-Test
WHEN OPERATING THIS
APPLIANCE WITH PROPANE,
ALL INSTRUCTIONS AND
WARNINGS MUST BE
OBSERVED. FAILURE TO DO
SO MAY RESULT IN A FIRE
OR EXPLOSION CAUSING
SERIOUS INJURY OR DEATH.
Light
switch
Light
switch
Grill lights
(not shown)
Connect
Note: Grill must be connected to 120VAC power for electronic lighting.
1. Open lid(s) or remove cover(s) from burner(s) to be lit.
2. Turn all gas control knob(s) to their OFF position(s).
3. Turn on the gas at its source.
Note: DO NOT turn on more than one valve at a time for either electronic or manual lighting.
4. Depress the desired control knob for 5 seconds, then, while pressing turn it
counterclockwise to the HI LIGHT position. Once the burner lights, release the knob.
CAUTION: If a burner does not light within fi ve (5) seconds of turning on the control knob,
depress the knob and turn it to the OFF position. WAIT FIVE (5) MINUTES before
repeating step 4. If the burners still do not light after several attempts, refer to the
LIGHTING INSTRUCTIONS in your grill owner’s manual.
5. Repeat step 4 for each additional burner to be lit.
Fig. 5-1 - Burner valve control knob
OFF
HI
LIGHT
LOW
T
O
TURN OFF
T
O
TURN
ON
Read setting
here
HIGH to
LIGHT
To
Turn
OFF
To
T
urn
ON
High to
light
Read setting here
REV 0 - 1409250910 L-C2-446
E-burner *
(pre-installed)
* The burner ports
and carry-over slots
must be kept clean to
ensure proper ignition
and operation.