Cybex 13070-999 VR1 Arm Curl - Manual (Page 9)

Cybex Owner’s Manual
9
1
1 4800-557
13000-552
Decal, Weight Plate (10-150) (Light)
Decal, Weight Plate (10-220) (Standard)
125 1:1
OWATONNA
MFG. APPR. TECH. PUBS. APPR. DATE DATE
REV. DWG. NO. SCALE SIZE CHECKED BY DWG. BY
TITLE:
FINISH:
MATERIAL:
B SHEET
OF 2 2
EXCEPT AS NOTED
GENERAL TOLERANCES:
2 DECIMALS ± .03 3 DECIMALS ± .015 ANGLES ± 1° FEATURES SHOWN PERPENDICULAR OR PARALLEL SHALL BE SO WITHIN ± 1°
REMOVE ALL BURRS BREAK SHARP EDGES .005/.010 R SURFACE FINISH INDICATED PER ANSI B46.1-1985
GENERAL MACHINING
DIMENSIONS
IN INCHES
DATE DATE REMOVE CARBURIZATION AND SCALE FROM LASER AND PLASMA CUT EDGES
ALL MATERIAL MUST COMPLY TO EUROPEAN UNION DIRECTIVE 2002/95/EC RoHS (RESTRICTION OF HAZARDOUS SUBSTANCES)
NOTES:
1. Font - 40 POINT HELVETICA BOLD. HORIZONTAL SCALE 80%. TRACKING -50.
13000-552
1/8/07 REL
-
DECAL, WT PLATE (10 - 220)
1/11/07 BB
1
9 4700-337
13000-030
Weight Stack Plate (Light)
Weight Plate Pack (Light)
96
38
WEIGHT PLA
TE DET
AIL
LIGHT ST
ACK 13000-032
STANDARD ST
ACK13000-036
96B
38
100
98 99
97
96A
14 plates 4700c070
9 plates 4700c073
LIGHT ST
ACK 13000-030
STANDARD ST
ACK 13000-034
STANDARD ST
ACK 13000-035
12 plates 4800-262
13000-551
4700-337
LIGHT ST
ACK 13000-033
13000-552
13000-553
4700-338
STANDARD ST
ACK 13000-036
STANDARD ST
ACK 13000-035
12 plates 4800-262
STANDARD ST
ACK 13000-033
1
9 4700-338
13000-034
Weight Stack Plate (Standard)
Weight Plate Pack (Standard)
96
38
WEIGHT PLA
TE DET
AIL
LIGHT ST
ACK 13000-032
STANDARD ST
ACK13000-036
96B
38
100
98 99
97
96A
14 plates 4700c070
9 plates 4700c073
LIGHT ST
ACK 13000-030
STANDARD ST
ACK 13000-034
STANDARD ST
ACK 13000-035
12 plates 4800-262
13000-551
4700-337
LIGHT ST
ACK 13000-033
13000-552
13000-553
4700-338
STANDARD ST
ACK 13000-036
STANDARD ST
ACK 13000-035
12 plates 4800-262
STANDARD ST
ACK 13000-033
Move to desired location
If Then
If machine can be
moved without
adding or removing
weight stacks.
Two people will be required for this procedure
1. Move to desired location.
2. Remove the four shipping cones using a 3/4” socket or wrench.
3. Attach foot pads to each foot of frame.
If Then
If machine needs
weight stacks
removed before
moving to desired
location.
Two people will be required for this procedure
1. Remove the two Button Head Socket Cap Screws (BHSCS)
securing the top cap to the frame using a 7/32” Allen wrench.
BHSCS
Top Cap
Shroud
2. Remove top cap and BHSCS.
3. Lift shroud up and out of machine.