beautypg.com

Aervoe Power Center 100 User Manual

Max burton, Power center #6994

background image

IMPORTANT SAFEGUARDS

Read all instructions before operating. Failure to follow all instructions may cause serious injury or

property damage. Keep a copy with the Power Center or inside the Jumper Cable access door for

reference.

CAUTION: To avoid electric shock and injury:

• Do not submerge the unit or its accessories in any liquid

• Keep electrical outlets and cables dry and out of severe weather

• Make sure all cables and adapters are connected correctly and in good condition. Never use

if they become worn or wires are exposed.

• Contains high voltage electronics and battery

Keep upright on a level surface to prevent obstructing vents

Do not look directly at the spotlight

Do not operate at temperatures below 14

ºF (-10ºC) or above 120ºF (49ºC)

Observe proper battery disposal requirements for your area and follow removal and

replacement instructions in the Care and Maintenance Section

Administer close supervision when using around children

NOTES AbOUT chARGING AND USING STORED POwER:

Stored power may be used at the same time the unit is charging using any of the following methods.

A built-in Battery Protection Circuit is included and audible beeps and visual cues on the LCD

Display will alert any over voltage, low voltage, or over heating conditions.

chARGING ThE POwER cENTER

120V Charging:

1.

Plug the included 120V AC adapter into an electrical wall outlet

2.

Plug the other end of the adapter into the DC IN #1 PORT of the unit

3.

The BATTeRy LeVeL INDICATOR will blink with the available battery capacity on the LCD

DISPLAy while charging.

12V Charging:

1.

Plug the included 12V DC adapter into a vehicle power recepticle

2.

Plug the other end of the adapter into the DC IN #2 PORT of the unit

3.

The BATTeRy LeVeL INDICATOR will blink with the available battery capacity on the LCD

DISPLAy while charging.

Dynamo Hand Crank Charging:

1.

Open the HAND CRANK arm and rotate clockwise at approximately 80-120 cycles/minute.

CAUTION: Turning at speeds greater than 120 cycles/minute may cause the unit to overheat.

2.

The BATTeRy LeVeL INDICATOR will blink with the available battery capacity on the LCD

DISPLAy while charging. Charging times will vary depending on crank speed and existing

battery level.

3.

Close the HAND CRANK.

Solar Charging (solar panel not included):

1.

Plug a compatible solar panel into the DC IN #2 PORT using the cord that comes with the solar

panel.

2.

Follow the instructions included with your solar panel and place it and the POweR CeNTeR in

direct sunlight.

3.

The BATTeRy LeVeL INDICATOR will blink with the available battery capacity on the LCD

DISPLAy while charging. Charging time will depend on the solar collector used and the

intensity of sunlight available.

NOTe: The Power Center will charge to 14.5V DC and 100% capacity initially from all methods

above and then settle at 13V DC and 85% capacity.

SPOTlIGhT OPERATION

Press the ON/OFF button:

1 time for 1 watt spotlight

2 times for flashing red 3 LeD emergency light

3 times for off

120V Ac POwER SUPPly (100 watt-hour)

1.

Press and hold the AC button for 3 seconds until AC OUTPUT appears on the LCD DISPLAy. It

is now ready to operate an appropriate 120V device (100 watts or less).

2.

Insert the 120V plug of the device into the 120V AC OUTPUT.

3.

The temperature and device wattage will be displayed on the screen.

4.

To deactivate the AC power supply, remove the plug and press the AC button for 3 seconds

until the AC Output function disappears.

12V Dc POwER SUPPly (100 watt-hour)

1.

Insert the plug of a 12V device into the 12V DC OUTPUT. It is now ready to operate an

appropriate 12V device (150 watts or less).

2.

To deactivate the DC power supply, remove the plug from the outlet.

USb cONNEcTION

1.

Press and hold the USB button for 3 seconds until USB OUTPUT shows on the LCD DISPLAy.

It is now ready to operate an appropriate device.

2.

Insert the plug of the USB device into the USB PORT.

3.

To deactivate the USB function, remove the plug and press the USB button for 3 seconds until

the USB Output function disappears.

VEhIclE JUMP STARTER

CAUTION: To prevent short circuit, explosion, and serious injury, keep metal parts away from the

positive and negative clamps and keep the clamps from touching each other. Check the condition of

the vehicle battery’s poles before connecting the jumper cables.

1.

Instructions and diagrams are also printed inside of the jumper cable door.

2.

Make sure the battery capacity is above 12V DC prior to jump starting. If it is not, use any of

the charging methods above to bring it up to the 12-14V range.

3.

Open the CABLe DOOR and take out the ReD and BLACK CLAMPS.

4.

Unscrew the BLACK NUT from the NegATIVe TeRMINAL and connect the RINg on the BLACK

wIRe to the NegATIVe TeRMINAL.

5.

Screw the BLACK NUT back onto the NegATIVe TeRMINAL to ensure a good connection.

6.

Repeat the process for the ReD NUT and ReD wIRe for the POSITIVe TeRMINAL.

7.

Clamp the black clamp to the negative pole of the car battery first, then clamp the red clamp to

the positive pole.

8.

Start the vehicle. If the vehicle fails to start, use the hand crank for 10 minutes or longer to

boost the power in the battery. If the vehicle still does not start after several attempts the

vehicle’s battery may be defective or reached it’s life expectancy and need to be replaced.

Consult a qualified repair facility.

clOcK

1.

The time should appear in the LCD DISPLAy. If it isn’t, press and hold the AC button to switch

back to clock display.

2.

Press and hold the SeT button until the hour blinks. Press AC to increase or USB to decrease

the setting.

3.

Press SeT button and the minutes will blink and set as above.

4.

Press the SeT button again to change between 12 and 24 hour formats.

cARE AND MAINTENANcE

Clean the body with a damp cloth. Soap and water may be used but it should never be

immersed or allow liquid to enter any open electronic circuits. Do not use any harsh solvents

or chemicals.

Store in a well-ventilated, dry environment.

Unit may be stored fully for 90+ days and it will be ready for use. It should be checked every 3

months and kept charged.

Battery Disposal:

Dissipate all battery power from unit. Have a qualified electrician verify the battery meter

is at 0%

Remove the 12 housing screws on the back panel. Remove battery and carefully

disconnect the wires from battery.

Dispose or recycle the old battery in accordance with all local disposal requirements.

Replace with a new battery with equal specifications by reversing the steps above.

Power Center

Spotlight/Flasher On/Off Button

Spotlight

LCD Display
Control Panel

Handle

Hand Crank

Jump Start Cable Access

Charging

Input/Output

Access

12V DC Output

& Fuse

Not visible (inside access door):

• 120V AC Inverter Fuse

• LCD Display Reset Button

Charging Access Door

USB Output

120V AC Output

120V AC In 12V DC In

DC IN #2

DC IN #1

.

W A R N I N G

HIGH VOLTAGE

5

Warning

Indicator

Warning

Indicator

Battery Level

Indicator

Battery Capacity

AC Watt/Clock

AC Output

Function

USB Output

Function

Clock Set

Current

Battery

Voltage

Temperature

Operation

Function

Control Panel

Max Burton

®

Power Center #6994

PARTS IDENTIFIcATION

Male Plug

120V AC Charging

Adapter

12V DC Charging

Adapter