Empty the water tank (fig. d) – Toyotomi TD-Z110 User Manual

Page 5

ENGLISH

AUTO DRY MODE
OPERATING STEPS:
1.

PRESS “POWER” BUTTON (C1) TO “ON”.

PRESS AUTO DRY MODE BUTTON.
Press the “AUTO DRY” mode button (C2) to set your desired
mode “AUTO”, “LOW” or “HIGH”.
AUTO mode (C16)
Keeps the room at a comfortable relative humidity (rh) level.
The unit automatically keeps room humidity at 45~50%rh with
automatic high or low fan speed.
LOW mode (C15)
Run in low fan speed.
The unit automatically dehumidify in low fan speed and low
heater.
HIGH mode (C14)
Super dry mode to prevent condensation.
The unit automatically keeps room humidity at 35~40%rh to
prevent condensation in the room.

PRESS AUTO LOUVER BUTTON
Press the Auto louver button (C4) to select your desired air
louver angle (C9, C10, C11). Please refer to the detailed in-
struction at below.

STOP OPERATION
Press the “POWER” button (C1) and all lights will go out.
CAUTION: After turning the appliance OFF using the Power

button, the fan will continue to run for two min-
utes. This is a normal procedure and helps to cool
and protect the internal components. During these
two minutes, DO NOT remove the power plug
from the electrical socket outlet; wait for the fan to
stop running.

LAUNDRY DRY MODE
OPERATING STEPS:
1.

PRESS “POWER” BUTTON (C1) TO “ON”.

PRESS LAUNDRY DRY MODE BUTTON.
Press the “LAUNDRY DRY” mode button (C3) to set your de-
sired mode “SAVING” or “TURBO”.
SAVING mode (C13)
Suitable for when the laundry amount is small or in summer to
save power.
The unit automatically shifts to provide warm air or fan air de-
pending on the room temperature. Assists to dry clothes with
low power and lower room temperature.
TURBO mode (C12)
Suitable for when the laundry amount is large or in winter to
dry clothes effectively.
The unit automatically provides heated air to dry clothes faster
with higher power.

PRESS AUTO LOUVER BUTTON
Press the Auto louver button (C4) to select your desired air
louver angle. (C9, C10, C11) Please refer the detailed instruc-
tion at below.

STOP OPERATION
Press the Power button (C1) and all lights will go out.
CAUTION: After turning the appliance OFF using the Power

AUTO SWING LOUVER (Fig. G)
By pressing the Auto Louver button (C4), select your desired
air louver angle and the Louver setting indicator lamp will light.
UP

➞ FRONT ➞ WIDE ➞ HOLD (Lamp off) ➞ UP

UP (G1)..........The automatic louver swings in an upward range

of approx. 90˚

FRONT (G2)...The automatic louver swings in a front range of

approx. 60˚

WIDE (G3)......The automatic louver swing in a wide range of

approx. 150˚

HOLD ............The automatic louver stops swinging when you

press Auto louver button and turns the lamp off.

The auto louver modes are useful for speeding up the drying
of washing, wardrobes and walls because the fact that the air-
flow is hitting the surface of whatever it is that you want to dry
will speed up the drying process as the water molecules will
be forced out faster.

WIDE / SPOT ADJUSTABLE LOUVER (Fig. H)
Wide blowing (H1)

➞ Adjust the blades outwards for an ex

panded airflow.

Spot blowing (H2)

➞ Adjust the blades inwards for a spot air

flow.

DOWNWARD ADJUSTABLE LOUVER (Fig. I)
1.

To pull out the louver, holding both ends and pull out. Lock
the louver by turn the portion upward central. (I1)

To place back the louver, unlock the louver by pushing the por-
tion downward central. Holding both ends and push back. (I2)

TIMER OPERATION
Auto turning OFF:
Press the Timer Key (C5) to select your desired running time (2,4 or
8 hours) (C8). The unit will automatically switch off at the end of the
selected time period. As the time counts down, the lamp (4 or 2
hours) will indicate the time remaining.
When no Timer is set (the lamp is off), the unit will run continuously
unless the water tank is already full.
2hours

➞ 4hours ➞ 8hours ➞ Continuous (lamp OFF) ➞ 2hours

CONTINUOUS DRAINAGE MODE (Fig. E)
For continuous drainage, use a hose with an inner diameter of
12mm and outer diameter of 14mm~16mm.
1.

Remove the water tank.

Use a screwdriver to remove the knockout at the back. (E1)
Pushing down and hold the stopper (E4) for drainage pipe by
finger (Fig. E2). Attach the hose to the drainage pipe (E5)
through the hole (Fig. E3).

Remove the tank cover and restore the water tank into the unit.
If the tank is not restored in the unit, full tank lamp will light
and cannot start operation.

The tubing should be lead to the drain with no sharp bends.
(E6, E7, E8)
NOTE:
1. The water tank must be in the correct position before tubing.
2. Remove the tubing before pulling out the water tank.
3. Remove the hose from the continuous drainage hole. Be

sure to put the tank cover on the water tank and restart op-
eration.

4. EMPTY THE WATER TANK (Fig. D)

When the water tank is full, the Water full indicator lamp will
light and unit stops in a few minutes.
NOTE: DO NOT move the unit or remove the water tank, if the

unit is still operating, as water may leak, damage the
unit or cause an electric shock.

By gripping the bottom of the water tank, remove the water
tank (D1) and lift carefully with handle (D2)

Remove the cover of bucket first (D3), then pour the water
away, (D4). Clean the water tank and restore the cover and the
water tank (D5) to the correct position.
NOTE:

•

Clean the water tank with clean water if needed. DO
NOT use solvent, abrasive or hot water.

•

DO NOT remove or damage the float in the tank, or the
unit cannot work correctly.

•

The water tank cover must be well fitted in position.

•

The water full indicator lamp lights if the water tank is
not well in the position.

CLEANING
CLEANING AIR INTAKE GRILLE (Fig. J)
If the filter is covered with dust, the airflow and the performance of
the unit will be affected. It is recommended to check and clean the
air filter every 2 weeks.
1.

Turn off the unit and remove the filter from the unit. (J1)

Clean the nano-silver filter with a vacuum cleaner or wash with
water (under 40˚C). (J2) If you wash with water, dry it com-
pletely at shaded area.

Replace the filter in position.

CLEANING SURFACE
1.

Turn off the unit, wait for the fan to stop and unplug from the
power socket.

Clean the surface with a soft damp cloth.

Dry thoroughly with a towel after cleaning.

In order to avoid damage, do not wash the unit with water, or
let water drip into the air inlet or outlet.

TD-Z110.qxd 14.5.22 16:25 ページ 2