Toyotomi FF-V30T - Manual (Page 12)

1. Set the Weekly Timer
NOTE: The following programs are set at the factory in advance.
After setting the current time and a day of the week, press the “TIMER” button to enter the weekly timer setting
mode. The “TIMER” is shown on the display. When the “TIMER” button is pressed during setting of the weekly
timer, the “TIMER” sign is disappeared and the current clock time and a day of the week are shown on the
display.
NOTE: You cannot enter the weekly timer setting mode, while in operation at AUTO operation mode.
1) Select the program number
Press the “ ▲MIN.” button or the “▼HOUR” button to select the program number.
The number of the program is 30. The unsetting program number is flashing on the display. In the case of the first
setting of the weekly timer, “P01” is shown on the display and will blink. When the unsetting program number is
shown on the display, all of a day of the week will also blink.
When pressing the “ ▲MIN.” button, the sign will change as follows.
“P01” ➞ “P02” ➞ ··· ➞ “P29” ➞ “P30”
When pressing the “ ▲MIN.” button at the position of “P30”, you can hear the beep sound and “P30” is not
changed any more.
When pressing the “ ▼HOUR” button, the sign will change as follows.
“P30” ➞ “P29” ➞ ··· ➞ “P02” ➞ “P01”
When pressig the “ ▼HOUR” button at the position of “P01”, you can hear the beep sound and “P01” is not
changed any more.
Basically, the only next program number of the biggest set program number is shown on the display and blinks.
All of 30 programs will not be shown on the display.
In case that the program is already set, the next number of the biggest setting program number is shown on the
display. If the program is set until “P30”, “P30” is shown on the display and will blink. Even though the program is
set until “P30”, if there is the unsetting program number, the smallest unsetting program number is shown on the
display.
Example:
In case that “P01” and “P02” programs are set and “P03” is not set, the display is indicated as follows.
“P01” – lighting ⇔ “P02” – lighting ⇔ “P03” – flashing 3
In case that “P01” and “P04” programs are set and “P02” and “P03” are not set, the display is indicated as
follows.
“P01” – lighting ⇔ “P02” – flashing 3 ⇔ “P03” – flashing 3 ⇔ “P04” – lighting ⇔ “P05” – flashing 3
Press the “SET” button to move to the next step (Set the timer).
The program number is eliminated by holding the “CLEAR” button continuously for 3 seconds.
Temp.
20˚C (68˚F)
16˚C (62˚F)
20˚C (68˚F)
16˚C (62˚F)
20˚C (68˚F)
16˚C (62˚F)
20˚C (68˚F)
16˚C (62˚F)
Day
“MON” “TUE” “WED” “THU” “FRI”
“MON” “TUE” “WED” “THU” “FRI”
“MON” “TUE” “WED” “THU” “FRI”
“MON” “TUE” “WED” “THU” “FRI”
“SUN” “SAT”
“SUN” “SAT”
“SUN” “SAT”
“SUN” “SAT”
Program #
P01
P02
P03
P04
P05
P06
P07
P08
Clock Time
6:00
8:30
17:00
23:00
7:00
10:00
16:00
23:00
11
FF_V30T_Type B_US.qxd 14.6.2 11:50 ページ 11