Atlona AT UHD CLSO 824 - Manual (Page 24)

24
atlona.com
Toll free: 1-877-536-3976
Local: 1-408-962-0515
Commands
The command codes are case sensitive, do not change capitalization, spacing, or lettering.
Command Feedback Description
PWON PWON Takes unit out of standby
PWOFF PWOFF Puts unit into standby
PWSTA PWx Will display power status
VersionX X.X.XX Displays the current firmware version X = MCU, FPGA, OSD, or DSP
Type AT-UHD-CLSO-824 Displays unit model number
Lock Lock Disables front panel buttons
Unlock Unlock Enables front panel buttons
All# x1AVx1, x2AVx2 Resets all inputs to corresponding outputs
x1$ y
Ex. x2$ off x1$ y
Ex. x2$ off Turns on and off output video y=on, off, or sta
Ex. Turns video off for output 2
x1All
Ex. x5All x1All
Ex. x5All Sets input to all outputs
Ex. Set input 5 to all outputs
x1AVx2
Ex. x3AVx2 x1AVx2
Ex. x3AVx2 Switch input to output
Ex. Set input 3 to output 2
x1AVx1,x2
Ex. x3AVx1,x2 x1AVx1,x2
Ex. x3AVx1,x2 Switch input to multiple outputs
Ex. Switch input 3 to outputs 1 and 2
VGAMSet X
Ex. VGAMSet comp VGASet X
Ex. VGAMSet comp Sets the analog VGA port to accept VGA (vga) or Component (comp)
Ex. Set the VGA port to accept component video
IRON IRON Turns the front panel IR receiver on
IROFF IROFF Turns the front panel IR receiver off
Statusx1
Ex. Statusx2 x1AVx3
Ex. x5AVx2 Shows the input currently connected to the output
Ex. Show input status of output 2 - Input 5 is currently selected
Status x4AVx1,x3AVx2 Displays the current input and output routes
SaveY
Ex. Save2 SaveY
Ex. Save2 Save the current input/output route to memory
Ex. Save the current input/output route to memory 2
RecallY
Ex. Recall4 RecallY
Ex. Recall4 Recalls the saved input/output memory
Ex. Recalls the input/output route from memory 4
ClearY
Ex. Clear3 ClearY
Ex. Clear3 Erases the input/output route from the selected memory number
Ex. Removes the saved input/output route from memory 3
Mreset Mreset Sets matrix settings back to factory settings
RS232zoneX[command]
Ex. RS232zone1[turnon] RS232zoneX[command]
Ex. RS232zone1[turnon] Send command through the RS-232 port of the HDBaseT receivers
Ex. Sends command turnon to the display connected to output 1
Baud Rate
Zone RS-232 port configuration must match the connected device on all parameters including baud
rate, data-length, parity, and stop-bit. These parameters can easily be set using the WebGUI or
following commands through RS-232 or TCP/IP.
The baud rate for the switcher is for switcher control and the transmitter/receiver baud
rate is for control of the RS-232 device in zone. All commands from your control processor are
at the settings for the switcher. The switcher will modify the baud rate and other settings to these
set parameters by zone.
Note: Baud rate options 2400, 4800, 9600, 19200, 38400, 57600, 115200, or 230400
Note: Default for the switcher is: Baud rate-115200bps, Data length-8bit, Parity-None, Stop Bit-1
Command for Switcher Parameters
CSpara[baudrate,data-length,parity,stop-bit] (data, parity, and stop bit for switcher must be 8,0,1)
For example if you wish to change the baud rate of the switcher to 38400 the command would
look like this:
CSpara[38400,8,0,1]