Ryobi RY80940 SERIES - Manual

ABRASIVE GENTLE
990000681
8-22-13 (REV:01)
Raise the handle (see page 8).
WARNING:
This Quick Reference Guide is not a substitute for reading the operator’s manual. To reduce the risk of injury or death, user must read and understand operator’s manual before using this product. All page references refer to
the operator’s manual.
FIRST TIME ASSEMBLY
1
RY80940 SERIES QUICK REFERENCE GUIDE
STARTING THE UNIT (COLD START) USING DETERGENT
2
Connect the high pressure hose to the pump
(see page 9).
6
Install the trigger handle holder, spray wand
holder, and hose storage (see page 8).
Assemble the trigger handle (see page 8).
3 Add entire bottle of lubricant provided to the pres-
sure washer (see page 10).
8
Completely uncoil garden hose or remove
completely from reel to prevent kinks.
Turn water faucet on fully.
Make sure there are no leaks.
With no nozzle installed, squeeze the trigger
to relieve air pressure. Hold the trigger until a
steady stream of water appears.
Add fuel (see page 10).
1
2
Put choke lever in START position (see page 11). 3
Pull starter grip and rope to start (see page 11).
5
Turn the fuel valve to ON (see page 11).
Put on/off switch in ON position (see page 11).
4
Allow engine to run for several seconds, then
move choke to RUN position (see page 11).
NOZZLE SELECTION GUIDE
Use of soap nozzle will activate detergent injector at a
20:1 dilution ratio.
WARNING! Never use bleach or solvent-based detergent.
BEFORE STORING THE UNIT
Add Pump Protector to the unit after each use and before storing. This will significantly improve pump
life (see page 15).
To order Pump Protector, call customer service at 1-800-860-4050.
To add, follow the instructions provided by the Pump Protector manufacturer.
1
Use the chart below to determine the correct nozzle for your job.
HIGH PRESSURE
(NO SOAP WHEN USING
THESE NOZZLES)
LOW PRESSURE
(FOR SOAP OR
GENTLE RINSE)
0º 25º 40º Long Range Short Range
Concrete, Brick, Masonry
    
Siding, Gutters, House
   
Fencing, Deck, Patio
   
Lawn Equipment, Boat, RV
   
 Recommended Nozzle  Use With Caution for Certain Applications
Turn the fuel valve to OFF before adding
lubricant.
Set unit on flat surface so engine is level.
Remove dipstick, wipe clean, put back in hole
(but don’t screw in) and check lubricant level.
This is a 4-cycle engine. Do not mix fuel and
lubricant together.
Add fuel stabilizer every time you fuel the
machine.
RESTARTING THE UNIT
(HOT RESTART)
6
If the engine does not start:
•
check for enough fuel;
• may need to adjust choke position;
• try starting again.
PUMP
PROTECTOR
Connect the high pressure hose to the trigger
handle (see page 9).
4
Connect your garden hose to the pressure washer
(see page 9).
7
FUEL
VALVE ON
CHOKE LEVER
(START)
ON/OFF
SWITCH
(ON)
CHOKE LEVER
(RUN)
DO NOT OVERTILT THE UNIT!
Pull starter grip and rope to start (see page 11).
1
2 Install nozzle and rotate
selector to blue or blue
setting (see page 13).
Completely uncoil and straighten high pressure
hose to prevent kinks.
1 Pour pressure washer
detergent in detergent tank
(see page 13).
3 Squeeze trigger and wait
approx. 5 seconds for soap
(see page 13).
5 S
SO AP
SO AP
DETERGENT
5 S
SO AP
If you need more assistance, visit our website at
www.ryobitools.com or call us at 1-800-860-4050.
• Will damage your pump
• Will void your warranty
• Will damage plants/shrubs
NOTICE:
Do not use E15 or E85 fuel (or fuel con-
taining greater than 10% ethanol) in this
product. It is a violation of federal law
and will damage the unit and void your
warranty.