Ryobi RY80518 - Manual

HIGH PRESSURE
(NO SOAP)
LOW PRESSURE
(FOR SOAP OR
GENTLE RINSE)
25º Green 40º White Blue Soap Nozzle
Concrete, Brick, Masonry
  
Siding, Gutters, House
  
Fencing, Deck, Patio
  
Lawn Equipment, Boat, RV
  
 Recommended nozzle  Use with caution for certain applications
990000549
2-26-13 (REV:01)
WARNING:
This Quick Reference Guide is not a substitute for reading the operator’s manual. To reduce the risk of injury or death, user must read and understand operator’s manual before using this product. All page references refer to
the operator’s manual.
FIRST TIME ASSEMBLY
RY80518 SERIES QUICK REFERENCE GUIDE
STARTING THE UNIT (COLD START) USING DETERGENT
2
Install the handle (see page 8).
Add entire bottle of lubricant provided to the pres-
sure washer (see page 10).
Attach the detergent injection hose to the pump.
(see page 8).
9
4
Completely uncoil garden hose or remove
completely from reel to prevent kinks.
Turn water faucet on fully.
Make sure there are no leaks.
With no nozzle installed, squeeze the trigger
to relieve air pressure. Hold the trigger until a
steady stream of water appears.
Add fuel (see pages 10 and 11).
1
2
Pull recoil starter to start (see page 11). 3
Turn the fuel valve to the ON position and pull the
choke out to the START position. (See page 11).
NOZZLE SELECTION GUIDE
Use of soap nozzle will activate detergent injector at a
20:1 dilution ratio.
WARNING! Never use bleach or solvent-based detergent.
•
Will damage your pump
• Will void your warranty
• Will damage plants/shrubs
BEFORE STORING THE UNIT
Add Pump Protector to the unit after each use and before storing. This will significantly improve pump
life.
To order Pump Protector, call customer service at 1-800-860-4050.
To add, follow the instructions provided by the Pump Protector manufacturer. (See page 15)
1
Turn the fuel valve to OFF before adding lubricant.
Set unit on flat surface so engine is level.
Remove dipstick, wipe clean, put back in hole
(but don’t screw in) and check lubricant level.
This is a 4-cycle engine. Do not mix fuel and
lubricant together.
Add fuel stabilizer every time you fuel the
machine.
RESTARTING THE UNIT
(HOT RESTART)
If the engine does not start:
•
check for enough fuel;
• may need to adjust choke position;
• try starting again.
PUMP
PROTECTOR
Connect the high pressure hose to the trigger
handle (see page 9).
6
Connect your garden hose to the pressure washer
(see page 9).
Attach the wheel assembly (see page 8).
8
1
If you need more assistance,
visit our website at www.ryobitools.com
or call us at 1-800-860-4050.
DO NOT OVERTILT THE UNIT!
Pull recoil starter to start (see page 11).
1
2 Install blue soap nozzle
(see page 12).
If detergent injection
hose comes loose
from pressure washer,
reattach it here.
1 Place detergent injection
hose in the detergent
container (see page 13).
3 Squeeze trigger and wait
approx. 5 seconds for soap
(see page 13).
5 S
Assemble the trigger handle (see page 9).
5
Connect the high pressure hose to the pump
(see page 9).
7
Completely uncoil and straighten high pressure
hose to prevent kinks.
ABRASIVE GENTLE
DETERGENT
FUEL VALVE ON
CHOKE IN START
POSITION
Use the chart below to determine the correct nozzle for your job.
NOTICE:
Do not use E15 or E85 fuel (or fuel con-
taining greater than 10% ethanol) in this
product. It is a violation of federal law
and will damage the unit and void your
warranty.
3 Attach the spray wand storage bracket. Make sure
to install mounting pad between frame and bracket.
(See page 8).
Let engine run for several seconds, then push
choke in to RUN position. (see page 11).
4
CHOKE IN RUN POSITION
5 S
MOUNTING
PAD