Using the tomato & fruit strainer, Stuffer assembly, Warning – Weston #5 Deluxe Electric Meat Grinder User Manual

Page 8

-8-

-13-

NOTE: The Tomato & Fruit Strainer Attachment

cannot be used with meat products.
NOTE: Follow the “Food Safety Guidelines” in this

manual and as outlined by the U.S. Food and Drug

Administration (FDA) whenever using this appliance.

Keep meat/food refrigerated and covered. Do not

let meat/food sit out any longer than is necessary for

processing.

1. Cut large fruits and vegetables into quarters and

small fruits and vegetables in half.

IMPORTANT: Remove pits, stems, shells

and seeds before placing fruits or vegetables

into the

Tomato & Fruit Strainer to avoid

damaging the

Screen.

2. Place the fruits/vegetables in the

Tray. Do not

overfill the

Tray. DO NOT operate the Grinder without

the

Tray in place.

3. Place a bowl under the

Plastic Chute to collect juice and pulp. Place a bowl

under the

Screen outlet to collect skin and seeds.

4. Feed the fruits/vegetables into the

Grinder Head. Use the Stomper to push the

fruits/vegetables into the

Grinder Head. Never use your fingers!

11. When straining is complete, turn the

Motor Unit “off” and disconnect it from the

electrical outlet.
HELPFUL HINTS:

Rerun the skin and seeds through the

Food Strainer to extract any

leftover pulp & juice. Repeat as necessary.

Use a rubber spatula to scrape pulp from the

Screen into the Chute.

USING THE TOMATO & FRUIT

STRAINER

Not included with all grinders.

STUFFER ASSEMBLY

1. Place the

Plastic Washer then the Bushing Set onto the end of the Auger opposite

the

Pin (figure 3).

2. Carefully insert the

Auger into the Grinder Head.

3. Place the

Knife onto the square portion of the Auger Pin. The cutting edges of the

Knife should face outward (figure 4).

4. Place the

Coarse Grinder Plate onto the round portion of the Auger Pin. Align the

tabs on the

Grinder Plate with the notches in the Grinder Head.

5. Insert the

Stuffing Funnel through the Front Ring Nut (figure 3).

6. Screw the

Front Ring Nut/Stuffing Funnel assembly onto the Grinder Head until

firmly tight.

DO NOT over-tighten the Front Ring Nut to avoid damaging the Grinder

during operation.

7. Loosen the

Head Locking Knob on the side of the Motor Unit.

8. Install the

Grinder Head onto the Motor Unit (figure 3).

9. Tighten the

Head Locking Knob to secure the Grinder Head.

10. Install the

Tray onto the Grinder Head. Press the Tray down until fully seated (figure 3).

Figure 3

Front

Ring

Nut

Auger

Plastic

Washer

Grinder

Head

Motor

Unit

Tray

Stomper

Head

Locking

Knob

Knife

with

cutting

edges

facing

outward.

Figure 4

Grinding

Plate

Stuffing

Funnel

8. Install and firmly tighten the

Front Ring

Nut (make sure the tabs remain aligned with the

notches).

DO NOT over-tighten the Front Ring Nut

to avoid damaging the

Grinder during operation.

9. Loosen the

Head Locking Knob on the side

of the

Motor Unit.

10. Insert the

Screen end of the fully-assembled

Grinder Head through the outlet end of the Plastic

Chute (figure 9).
11. Install the

Grinder Head onto the Motor Unit.

12. Tighten the

Head Locking Knob to secure the

Head in place.
13. Install the

Tray onto the Grinder Head. Press the Tray down until fully seated (figure 9).

Figure 9

Reverse

Button

Power

Switch

Auger

Bushing

Set

WARNING! Before cleaning, assembling or disassembling the Grinder, make sure

it is turned “off” and disconnected from the power source. Test to make sure there is

no power to the

Grinder by switching the Motor Unit “on” and “off.”

Follow all of the Safety Rules

and Warnings in this manual

whenever using this appliance.

Never leave this

appliance unattended.

Disconnect from power supply

when not in use.

WARNING!

Keep fingers, hands,

other body parts and

foreign objects away

from the inlet during

operation!

Only use the provided

stomper to push food into

the appliance.

Keep children away!