Sioux Tools 1OM - Manual (Page 2)

2
GENERAL OPERATION
"1SM" LEVER OPERATED TOOLS
These tools are started by depressing the lever. The output spindle of the tool will not turn until the clutch is engaged by applying
pressure to the fastener after the air motor has started.
"1OM" TRIGGER OPERATED TOOLS
These tools are started by depressing the trigger. The output spindle of the tool will not turn until the clutch is engaged by applying
pressure to the fastener after the air motor has started.
Both lever operated and trigger operated reversing tools have a button to depress to reverse the air motor. Always depress
the button fully to obtain full power. The reversing button can be locked in the reverse direction by fully depressing and
rotating the button clockwise.
ADJUSTABLE CLUTCH OPERATION
Adjustable clutch tools will continue to ratchet when the preset torque is reached and can only be stopped by removing the tool from
the fastener.
Adjustable clutches are adjusted externally with the use of Sioux No. 2366 clutch adjustment wrench or a #1 (3/16", 4.8mm Dia.
shank) Phillips screwdriver. Clutch adjustment is accomplished by rotating the clutch cover until the slot in the clutch case appears.
Turn the output spindle of the tool with a 1/4 (6.4mm) hex key wrench until the groove in the adjusting washer is aligned with the slot
in the clutch case. Insert the clutch adjustment wrench into the groove and push to fully engage the teeth. Turn the clutch adjustment
wrench counterclockwise to increase the torque.
Three clutch springs are available and are color coded for torque range.
#66050 green spring 2-20 in-lb (.23-2.26 N
.
m)
#66049 blue spring 15-35 in-lb (1.7-4 N
.
m)
#66048 silver spring 30-50 in-lb (3.39-5.6 N
.
m)
DECLARATION OF CONFORMITY
We, Sioux Tools Inc., 250 Snap-on Drive, P.O. Box 1596, Murphy, NC, 28906, USA, declare under our sole responsibility that the products
1OM1101, 1OM1201, 1OM1301, 1OM1401, 1OM1501, 1OM1601, 1OM1103, 1OM1203, 1OM1303, 1OM1403, 1OM1503, 1OM1603, 1OM1105,
1OM1205, 1OM1305, 1OM1405, 1OM1505, 1OM1605, 1OM1107, 1OM1207, 1OM1307, 1OM1407, 1OM1507, 1OM1607, 1OM2101, 1OM2201,
1OM2301, 1OM2401, 1OM2501, 1OM2601, 1OM2103, 1OM2203, 1OM2303, 1OM2403, 1OM2503, 1OM2603, 1OM2105, 1OM2205, 1OM2305,
1OM2405, 1OM2505, 1OM2605, 1OM2107, 1OM2207, 1OM2307, 1OM2407, 1OM2507, 1OM2607, 1OM4303PQ, 1SM1101, 1SM1201,
1SM1301, 1SM1401, 1SM1501, 1SM1601, 1SM1701, 1SM1103, 1SM1203, 1SM1303, 1SM1403, 1SM1503, 1SM1603, 1SM1703, 1SM1105,
1SM1205, 1SM1305, 1SM1405, 1SM1505, 1SM1605, 1SM1705, 1SM1107, 1SM1207, 1SM1307, 1SM1407, 1SM1507, 1SM1607, 1SM1707,
1SM2101, 1SM2201, 1SM2301, 1SM2401, 1SM2501, 1SM2601, 1SM2103, 1SM2203, 1SM2303, 1SM2403, 1SM2503, 1SM2603, 1SM2105,
1SM2205, 1SM2305, 1SM2405, 1SM2505, 1SM2605, 1SM2107, 1SM2207, 1SM2307, 1SM2407, 1SM2507, 1SM2607
Includes products with ‘Y’ in the catalog number
to which this declaration relates are in conformity with the following standard or standards or other normative document or documents:
EN 792, ISO 12100-1, ISO 12100-2, ISO 8662, Pneurop PN8NTC1
following the provisions of
98/37/EC Directive.
May 1, 2009
Murphy, North Carolina, USA
Date and place of issues
Robert Hartman
Vice President and General Manager-Power Tools
Sioux Tools Inc.
Name and position of issuer Signature of issuer